REAR SEAT INNER BELT ASSEMBLY > INSTALLATION |
| 1. INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type RH Side) |
![]() |
Install the belt with the bolt.
| 2. INSTALL REAR NO. 1 SEAT ASSEMBLY RH |
Fully tilt the seatback forward.
Place the seat in the cabin.
Connection procedures of seat to lock cable when reusing seat:
![]() |
Using a screwdriver, detach the claw and remove the connector case from the seat.
![]() |
Install the connector case to the body's cap.
![]() |
Pull out the joint piece. Align the slits of the joint piece and connector case.
![]() |
Compress the spring of the adjuster, and pull out the cable from the seat's cap.
![]() ![]() |
Install the seat cable's end part to the connector case's slit.
![]() |
Install the seat's cap to the connector case.
Temporarily place the seat into the vehicle where it will be installed.
![]() |
Return the seatback to the upright position.
![]() |
Attach the claws of the connector and adjuster, and install them to the seat.
![]() |
Press the adjuster's lock piece to lock it.
Connection procedures of seat to lock cable when replacing seat:
![]() |
Cut the joint piece on the lock cable, and remove it.
Temporarily place the seat into the vehicle where it will be installed.
![]() |
Install the body's cap to the connector case.
![]() |
Press the adjuster's lock pin.
![]() |
Return the seatback to the upright position.
![]() |
Press the adjuster's lock piece to lock it.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
| 3. INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type LH Side) |
![]() |
Install the belt with the bolt.
| 4. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH |
![]() |
Install the belt with the bolt.
| 5. INSTALL REAR SEAT REAR BRACKET COVER LH |
![]() |
Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.
Install the 2 screws.
| 6. INSTALL REAR NO. 1 SEAT ASSEMBLY LH |
Fully tilt the seatback forward.
Place the seat in the cabin.
![]() |
Connection procedures of seat to lock cable when reusing seat:
Using a screwdriver, detach the claw and remove the connector case from the seat.
![]() |
Install the connector case to the body's cap.
![]() |
Pull out the joint piece. Align the slits of the joint piece and connector case.
![]() |
Compress the spring of the adjuster, and pull out the cable from the seat's cap.
![]() ![]() |
Install the seat cable's end part to the connector case's slit.
![]() |
Install the seat's cap to the connector case.
Temporarily place the seat into the vehicle where it will be installed.
![]() |
Return the seatback to the upright position.
![]() |
Attach the claws of the connector and adjuster, and install them to the seat.
![]() |
Press the adjuster's lock piece to lock it.
![]() |
Connection procedures of seat to lock cable when replacing seat:
Cut the joint piece on the lock cable, and remove it.
Temporarily place the seat into the vehicle where it will be installed.
![]() |
Install the body's cap to the connector case.
![]() |
Press the adjuster's lock pin.
![]() |
Return the seatback to the upright position.
![]() |
Press the adjuster's lock piece to lock it.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Tighten the 3 bolts on the rear side of the seat.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
| 7. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER RH |
![]() |
Install the belt with the bolt.
| 8. INSTALL REAR NO. 5 SEAT LEG SIDE COVER |
| 9. INSTALL REAR NO. 4 SEAT LEG SIDE COVER |
| 10. INSTALL REAR NO. 3 SEAT LEG SIDE COVER |
![]() |
| 11. INSTALL REAR NO. 2 SEAT LEG SIDE COVER |
| 12. INSTALL REAR SEAT LEG COVER |