Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL CUSHION
  1. Install the 2 cushions.



2. INSTALL FRONT DOOR WEATHERSTRIP LH


B129186
  1. Attach the 17 clips to install the weatherstrip.



3. INSTALL FRONT DOOR GLASS RUN LH


4. INSTALL FRONT DOOR CHECK ASSEMBLY LH


B061953E03
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for bolt A

  1. Apply adhesive to the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the door check to the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt B



5. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


B129193
  1. Attach the 2 claws to install the pad.



6. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


B129192
  1. Attach the 2 claws to install the pad.



7. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Install the front door lock open rod.



    B133179
  1. Attach the claw and clip to install the frame.



    B086435E02
  1. Using a T30 "TORX" socket, install the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B135427
  1. w/ Entry and Start System:
    Connect the clamp and connector.



8. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
  1. w/ Entry and Start System:
    Connect the connector.



    B129364
  1. Install the handle by pushing and sliding it in the direction indicated by the arrows in the illustration.



9. INSTALL FRONT DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B129196
  1. Install the 2 cables as shown in the illustration.



    B133182
  1. Attach the 3 claws to close the cover.



    B129194
  1. Install a new door lock wire harness packing.

    NOTICE:
    1. When reinstalling the door lock, always use new packing.
    2. Do not allow grease or dirt to contaminate the gap between the door panel and packing.
    3. Old or damaged packing cannot effectively protect against water which can damage the door lock.



    B065961E08
  1. Connect the control rod to the door lock, and then set it to the door panel.

    NOTICE:
    Make sure that the rod is securely engaged to the lock.

  1. Apply adhesive to the threads of the 3 screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B129199
  1. Using a T30 "TORX" socket, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



10. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)
  1. Install the door lock cylinder to the cover.



    B129201E01
  1. Using a T30 "TORX" socket, install the cover (with cylinder) with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



11. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Front Passenger Side)


B129203E01
  1. Using a T30 "TORX" socket, install the cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



12. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


B129171
  1. Install the frame with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



13. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B129173
  1. Using a T25 "TORX" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 49 in.*lbf }



14. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


B133185
  1. Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.



    B129170
  1. Install the regulator with the 6 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Connect the connector.



15. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


B129187E01
  1. Install the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.



    B129168
  1. Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



16. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH


    B130252
  1. Attach the claws to install the belt moulding.

    HINT:
    Confirm that the moulding is firmly installed.



17. INSTALL FRONT DOOR SERVICE HOLE COVER LH


B129188E01
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull out the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. Connect each connector.



18. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


B133476E01
  1. Connect the 2 cables to the inside handle.



19. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY


    B131481
  1. Install the speaker with the 2 screws.

  1. Connect the connector.



20. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    B131945
  1. Using an air riveter or hand riveter, install the speaker with 3 new rivets.

    NOTICE:

    1. B171664E02
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B172390E02
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet to the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. B172391E02
      Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.

  1. Connect the connector.



21. INSTALL OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH


B129405E03
  1. Pass the connector labeled A and wire harness of the mirror through the wire harness hole.

  1. Temporarily install the mirror by inserting the bosses on the mirror into the holes on the vehicle and temporarily installing the 3 screws.

  1. Tighten the 3 screws in the sequence shown in the illustration to install the mirror.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the connector labeled A.



22. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. Attach the 4 claws to install the speaker door grille.

  1. Attach the 7 claws to install the weatherstrip inner.



    B133485
  1. Attach the 2 claws to install the inside handle.



    B133484
  1. Attach the 10 clips to install the trim board.

  1. Install the 3 screws.



    B129164
  1. Attach the 3 claws to install the door inside handle bezel plug.



    B133479
  1. Attach the 12 claws to install the door assist grip.



23. INSTALL FRONT ARMREST BASE PANEL UPPER LH


B129161
  1. for Driver Side:
    Install the power window regulator master switch to the panel with the 3 screws.



    B137873
  1. for Passenger Side:
    Attach the 2 claws and install the power window regulator switch to the panel.

  1. Connect the switch connectors.



    B129160
  1. Attach the clip and 5 claws to install the panel (with the switch).



24. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


B129158
  1. Attach the clip and 3 claws to install the garnish.



25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL