1AZ-FE ENGINE MECHANICAL > TORQUE SPECIFICATIONS |
| Part Tightened | N*m | kgf*cm | ft.*lbf |
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 29.5 | 301 | 22 |
| No. 2 camshaft bearing cap x Cylinder head sub-assembly | 29.5 | 301 | 22 |
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf |
| No. 2 camshaft timing sprocket x No. 2 camshaft | 54 | 551 | 40 |
| No. 1 chain tensioner assembly x Timing chain cover sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
| No. 1 and No. 2 engine hanger x Cylinder head sub-assembly | 38 | 387 | 28 | |
| Chain tensioner plate x Cylinder block | 12 | 122 | 9 | |
| Oil pump drive shaft gear x Cylinder block | 29.5 | 301 | 22 | |
| No. 1 chain vibration damper x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Chain tensioner slipper x Cylinder block | 19 | 194 | 14 | |
| Timing chain guide x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Timing chain cover sub-assembly x Cylinder block | Bolt A = 10 mm head | 9.0 | 92 | 80 in.*lbf |
| Bolt B = 12 mm head | 25 | 255 | 18 | |
| Bolt C = 14 mm head | 55 | 561 | 41 | |
| Nut | 11 | 122 | 8 | |
| Stud bolt (for V-ribbed belt) x Cylinder block | 21.5 | 219 | 16 | |
| No. 1 chain tensioner x Timing chain tensioner sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Crankshaft pulley x Crankshaft | 180 | 1,835 | 133 | |
| Oil pan sub-assembly x Stiffening crankcase assembly | 9.0 | 92 | 80 in.*lbf | |
| V-ribbed belt tensioner assembly x Cylinder block | 59.5 | 607 | 44 | |
| Engine mounting bracket RH x Timing chain cover sub-assembly | 55 | 561 | 41 | |
| Cylinder head cover sub-assembly x Cylinder head | Bolt A | 11 | 112 | 8 |
| Bolt B (ignition coil side) | 14 | 143 | 10 | |
| Nut | 11 | 112 | 8 | |
| Engine wire x Cylinder head cover sub-assembly | 8.4 | 86 | 74 in.*lbf | |
| Idler pulley bracket x Cylinder block | 60 | 612 | 44 | |
| Engine mounting insulator RH x Body | 95 | 969 | 70 | |
| Engine mounting insulator RH x Engine mounting bracket | for bolt | 95 | 969 | 70 |
| for nut A | 95 | 969 | 70 | |
| for nut B | 52 | 530 | 38 | |
| Front engine mounting insulator x Front cross member | 95 | 969 | 70 | |
| Engine mounting insulator FR x Engine mounting bracket FR | 145 | 1,479 | 107 | |
| Radiator reservoir x Body panel | 5.0 | 51 | 44 in.*lbf | |
| No. 1 engine cover x Cylinder head cover sub-assembly | 7.0 | 71 | 62 in.*lbf | |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
| Camshaft position sensor x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Engine coolant temperature sensor x Cylinder head | 20 | 204 | 15 | |
| Oil pressure switch x Cylinder head | 13 | 133 | 10 | |
| Cylinder head x Cylinder block | 1 st | 78.5 | 800 | 58 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Camshaft timing gear assembly x Camshaft | 54 | 551 | 40 | |
| No. 2 camshaft timing sprocket x No. 2 camshaft | 54 | 551 | 40 | |
| No. 1 and No. 2 camshaft bearing cap x Cylinder head | 29.5 | 301 | 22 | |
| No. 3 camshaft bearing cap x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Exhaust manifold converter sub-assembly x Cylinder head | 37 | 377 | 27 | |
| No. 1 exhaust manifold heat insulator x Exhaust manifold converter sub-assembly | 12 | 122 | 9 | |
| No. 2 manifold stay x Exhaust manifold converter sub-assembly, Cylinder block | 44 | 449 | 32 | |
| Manifold stay x Exhaust manifold converter sub-assembly, Cylinder block | 44 | 449 | 32 | |
| Oil dipstick guide x No. 1 water by-pass pipe | 9.0 | 92 | 80 in.*lbf | |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
| No. 1 and No. 2 engine hanger x Cylinder head sub-assembly | 38 | 387 | 28 | |
| Drive shaft bearing bracket x Cylinder block | 64 | 653 | 47 | |
| Flywheel sub-assembly x Crankshaft | 130 | 1,326 | 96 | |
| Drive plate sub-assembly x Crankshaft | 98 | 1,000 | 72 | |
| Engine mounting insulator LH x Side member | 95 | 969 | 70 | |
| Engine mounting bracket LH x Engine mounting insulator LH | 56 | 571 | 41 | |
| Engine mounting insulator RH x Body | 95 | 969 | 70 | |
| Engine mounting insulator RH x Timing chain cover sub-assembly | for bolt | 95 | 969 | 70 |
| for nut A | 95 | 969 | 70 | |
| for nut B | 52 | 530 | 38 | |
| Engine mounting insulator RR x Center member | 95 | 969 | 70 | |
| Engine mounting bracket RR x Engine mounting insulator RR | 95 | 969 | 70 | |
| Engine mounting insulator FR x Front cross member | 95 | 969 | 70 | |
| Engine mounting bracket FR x Engine mounting insulator FR | 145 | 1,479 | 107 | |
| Battery carrier x Side member | 20 | 204 | 15 | |
| Battery bracket reinforcement x Battery carrier | 20 | 204 | 15 | |
| No. 1 battery carrier x Battery bracket reinforcement | 20 | 204 | 15 | |
| Air cleaner case x Body | 5.0 | 51 | 44 in.*lbf | |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
| Connecting rod cap x Connecting rod | 24.5 | 250 | 18 | |
| Crankshaft bearing cap x Cylinder block | 1 st | 40 | 408 | 30 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Stud bolt x Cylinder block | Bolt A (Bolt length = 84.0 mm) (3.31 in.) | 22 | 219 | 16 |
| Bolt B (Bolt length = 33.3 mm) (1.31 in.) | 5.0 | 51 | 44 in.*lbf | |
| Bolt C (Bolt length = 52.5 mm) (2.07 in.) | 9.5 | 97 | 84 in.*lbf | |
| Bolt D (Bolt length = 27.5 mm) (1.08 in.) | 5.0 | 51 | 44 in.*lbf | |
| Stiffening crankcase assembly x Cylinder block | 32.5 | 331 | 24 | |
| No. 1 taper screw plug x Cylinder block | 26 | 265 | 19 | |
| Plug (oil control valve filter) x Cylinder block | 30 | 306 | 22 | |
| Water drain cock plug x Cylinder block | 25 | 255 | 18 | |
| Cylinder head sub-assembly x Cylinder block | 1 st | 78.5 | 800 | 58 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Camshaft timing oil control valve assembly x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Oil drain plug x Oil pan sub-assembly | 40 | 408 | 30 | |
| Oil filer union x Stiffening crankcase assembly | 29.5 | 301 | 22 | |
| Ventilation valve sub-assembly x Cylinder head cover sub-assembly | 19 | 194 | 14 | |
| Oil filer cap sub-assembly x Cylinder head cover sub-assembly | 3.0 | 31 | 26 in.*lbf | |
| Oil cooler pipe x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Union bolt x Stiffening crankcase assembly | 25 | 255 | 18 | |
| No. 3 water by-pass pipe x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| No. 1 water by-pass pipe x Cylinder block | 9.0 | 92 | 80 in.*lbf | |