SFI SYSTEM > TERMINALS OF ECM |
| SFI SYSTEM |

| Symbol (Terminal No.) | Wiring Color | Terminal Description | Condition | STD Voltage |
| +B (A12-2) - E1 (B96-81) | B - BR | Power source of ECM | Ignition switch on (IG) | 9 to 14 V |
| +B2 (A12-1) - E1 (B96-81) | B - BR | Power source of ECM | Ignition switch on (IG) | 9 to 14 V |
| BATT (A12-20) - E1 (B96-81) | W - BR | Battery (for measuring the battery voltage and for the ECM memory) | Always | 9 to 14 V |
| +BM (A12-3) - E1 (B96-81) | LG - BR | Power source of ETCS throttle motor | Always | 9 to 14 V |
| MREL (A12-44) - E1 (B96-81) | O - BR | EFI relay operation signal | Ignition switch on (IG) | 9 to 14 V |
| VCTA (B96-96) - ETA (B96-97) | B - W | Power source for throttle position sensor (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| VCV1 (B96-115) - E1 (B96-81) | G-R - BR | Power source for VVT sensor (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| VCE1 (B96-114) - E1 (B96-81) | GR - BR | Power source for VVT sensor (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| VCE2 (B96-112) - E1 (B96-81) | Y - BR | Power source for VVT sensor (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| VCV2 (B96-113) - E1 (B96-81) | V - BR | Power source for VVT sensor (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| IGSW (A12-28) - E1 (B96-81) | B - BR | Ignition switch signal | Ignition switch on (IG) | 9 to 14 V |
| FC (A12-7) - E1 (B96-81) | W - BR | C/OPEN relay operation signal (fuel pump control) | Ignition switch on (IG), engine stopped | 9 to 14 V |
| FC (A12-7) - E1 (B96-81) | W - BR | C/OPEN relay operation signal (fuel pump control) | Ignition switch on (IG), engine idling | 0 to 1.5 V |
| STP (A12-36) - E1 (B96-81) | L - BR | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| STP (A12-36) - E1 (B96-81) | L - BR | Stop light switch signal | Brake pedal released | Below 1.5 V |
| ST1- (A12-35) - E1 (B96-81) | GR - BR | Stop light switch signal (opposite to STP terminal) | Ignition switch on (IG), brake pedal depressed | 7.5 to 14 V |
| ST1- (A12-35) - E1 (B96-81) | GR - BR | Stop light switch signal (opposite to STP terminal) | Ignition switch on (IG), brake pedal released | Below 1.5 V |
| VPA (A12-55) - E1 (B96-81) | W - BR | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), accelerator pedal released | 0.5 to 1.1 V |
| VPA (A12-55) - E1 (B96-81) | W - BR | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), accelerator pedal fully depressed | 2.6 to 4.5 V |
| VPA2 (A12-56) - EPA2 (A12-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal released | 1.2 to 2.0 V |
| VPA2 (A12-56) - EPA2 (A12-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal fully depressed | 3.4 to 5.0 V |
| EPA (A12-59) - VPA (A12-55) | Y - W | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), accelerator pedal released | 0.5 to 1.1 V |
| EPA (A12-59) - VPA (A12-55) | Y - W | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), accelerator pedal fully depressed | 2.6 to 4.5 V |
| EPA2 (A12-60) - VPA2 (A12-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal released | 1.2 to 2.0 V |
| EPA2 (A12-60) - VPA2 (A12-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal fully depressed | 3.4 to 5.0 V |
| TC (A12-27) - E1 (B96-81) | G - BR | Terminal TC of DLC3 | Ignition switch on (IG) | 9 to 14 V |
| VCPA (A12-57) - EPA (A12-59) | B - Y | Power source of accelerator pedal position sensor (for VPA) | Ignition switch on (IG) | 4.5 to 5.0 V |
| VCP2 (A12-58) - EPA2 (A12-60) | L - O | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch on (IG) | 4.5 to 5.0 V |
| TACH (A12-15) - E1 (B96-81) | GR - BR | Engine speed signal (for combination meter) | Idling | Pulse generation (see waveform 11) |
| CCS (A12-40) - E1 (B96-81) | L - BR | Cruise control main switch signal | Ignition switch on (IG) CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON | 10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V |
| SPD (A12-8) - E1 (B96-81) | V - BR | Vehicle speed signal from combination meter | Ignition switch on (IG), driving wheel rotated slowly | Pulse generation (see waveform 8) |
| W (A12-24) - E1 (B96-81) | R - BR | Malfunction Indicator Lamp (MIL) operation signal | Ignition switch on (IG) | Below 3.0 V |
| W (A12-24) - E1 (B96-81) | R - BR | Malfunction Indicator Lamp (MIL) operation signal | Idling | 9 to 14 V |
| CANH (A12-41) - E1 (B96-81) | Y - BR | CAN communication line | Ignition switch on (IG) | Pulse generation (see waveform 12) |
| CANL (A12-49) - E1 (B96-81) | W - BR | CAN communication line | Ignition switch on (IG) | Pulse generation (see waveform 13) |
| E1 (B96-81) - Body ground | BR - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| #10 (B96-45) - E01 (B96-22) #20 (B96-85) - E01 (B96-22) #30 (B96-44) - E01 (B96-22) #40 (B96-84) - E01 (B96-22) #50 (B96-43) - E01 (B96-22) #60 (B96-83) - E01 (B96-22) | Y - BR W - BR B - BR BR - BR L - BR G - BR | Fuel injector operation signal | Ignition switch on (IG) | 9 to 14 V |
| #10 (B96-45) - E01 (B96-22) #20 (B96-85) - E01 (B96-22) #30 (B96-44) - E01 (B96-22) #40 (B96-84) - E01 (B96-22) #50 (B96-43) - E01 (B96-22) #60 (B96-83) - E01 (B96-22) | Y - BR W - BR B - BR BR - BR L - BR G - BR | Fuel injector operation signal | Idling | Pulse generation (see waveform 3) |
| STA (A12-48) - E1 (B96-81) | LG - BR | Starter relay operation signal | Cranking | 9 to 14 V |
| OC2+ (B96-52) - OC2- (B96-51) | BR - B | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| OC1+ (B96-58) - OC1- (B96-57) | W - B | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| VV2+ (B96-67) - VV2- (B96-90) | W - B | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| VV1+ (B96-69) - VV1- (B96-92) | P - L-B | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| NE+ (B96-110) - NE- (B96-111) | G - R | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| EV2+ (B96-66) - EV2- (B96-89) | R - L | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV1+ (B96-68) - EV1- (B96-91) | Y - G | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| OE1+ (B96-56) - OE1- (B96-55) | LG - R | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| OE2+ (B96-50) - OE2- (B96-49) | W - B | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| M- (B96-18) - ME01 (B96-20) | R - BR | Throttle drive motor operation signal (negative terminal) | Idling with warm engine | Pulse generation (see waveform 10) |
| M+ (B96-19) - ME01 (B96-20) | G - BR | Throttle drive motor operation signal (positive terminal) | Idling with warm engine | Pulse generation (see waveform 9) |
| E02 (B96-21) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| E01 (B96-22) - Body ground | BR - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| IGT1 (B96-40) - E1 (B96-81) IGT2 (B96-39) - E1 (B96-81) IGT3 (B96-38) - E1 (B96-81) IGT4 (B96-37) - E1 (B96-81) IGT5 (B96-36) - E1 (B96-81) IGT6 (B96-35) - E1 (B96-81) | W - BR G-R - BR G - BR LG - BR P - BR V - BR | Engine coil with igniter (ignition signal) | Idling | Pulse generation (see waveform 6) |
| AICV (A12-4) - E1 (B96-81) | L - BR | VSV for air intake control system operation signal | Ignition switch on (IG) | 9 to 14 V |
| GE01 (B96-41) - E1 (B96-81) | BR - BR | Shielded earth (ground) circuit of throttle drive motor | Always | Below 1 V |
| OX1B (B96-88) - EX1B (B96-65) OX2B (B96-87) - EX2B (B96-64) | W - GR B - B-W | Heated oxygen sensor signal | With engine speed at 2500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| VTA2 (B96-99) - ETA (B96-97) | GR - W | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal fully released | 2.1 to 3.1 V |
| VTA2 (B96-99) - ETA (B96-97) | GR - W | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), accelerator pedal fully depressed | 4.5 to 5.0 V |
| VTA1 (B96-98) - ETA (B96-97) | Y - W | Throttle position sensor signal (for engine control) | Ignition switch on (IG), throttle valve fully closed | 0.5 to 1.2 V |
| VTA1 (B96-98) - ETA (B96-97) | Y - W | Throttle position sensor signal (for engine control) | Ignition switch on (IG), throttle valve fully open | 3.2 to 4.8 V |
| THW (B96-79) - ETHW (B96-78) | L - BR | Engine coolant temperature sensor signal | Idling, engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| THA (B96-71) - ETHA (B96-74) | P - G-R | Intake air temperature sensor signal | Idling, intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| IGF1 (B96-106) - E1 (B96-81) | Y - BR | Engine coil with igniter (ignition confirmation signal) | Ignition switch on (IG) | 4.5 to 5.0 V |
| IGF1 (B96-106) - E1 (B96-81) | Y - BR | Engine coil with igniter (ignition confirmation signal) | Idling | Pulse generation (see waveform 6) |
| E2G (B96-73) - E1 (B96-81) | LG - BR | Earth (ground) circuit of sensor for mass air flow meter | Always | Below 1 V |
| VG (B96-72) - E2G (B96-73) | GR - LG | Mass Air Flow (MAF) meter signal | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| ACIS (B96-107) - E1 (B96-81) | R - BR | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch on (IG) | 9 to 14 V |
| PRG (B96-108) - E1 (B96-81) | LG - BR | Purge VSV for EVAP system operation signal | Ignition switch on (IG) | 9 to 14 V |
| PRG (B96-108) - E1 (B96-81) | LG - BR | Purge VSV for EVAP system operation signal | Idling | Pulse generation (see waveform 7) |
| HA2A (B96-109) - E05 (B96-46) | B - BR | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA2A (B96-109) - E05 (B96-46) | B - BR | A/F sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| HA1A (B96-86) - E04 (B96-23) | G - BR | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA1A (B96-86) - E04 (B96-23) | G - BR | A/F sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| ME01 (B96-20) - E1 (B96-81) | BR - BR | Earth (ground) circuit of ECM | Always | Below 1 V |
| E03 (B96-104) - E1 (B96-81) | BR - BR | Earth (ground) circuit of ECM | Always | Below 1 V |
| HT2B (B96-47) - E1 (B96-81) HT1B (B96-48) - E1 (B96-81) | Y - BR LG - BR | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| HT2B (B96-47) - E1 (B96-81) HT1B (B96-48) - E1 (B96-81) | Y - BR LG - BR | Heated oxygen sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| E05 (B96-46) - E1 (B96-81) | BR - BR | Earth (ground) circuit of ECM | Always | Below 1 V |
| E04 (B96-23) - E1 (B96-81) | BR - BR | Earth (ground) circuit of ECM | Always | Below 1 V |
| NSW (B96-62) - E1 (B96-81) | G-R - BR | Park/Neutral position switch signal | Ignition switch on (IG), shift lever position P or N | Below 3.0 V |
| NSW (B96-62) - E1 (B96-81) | G-R - BR | Park/Neutral position switch signal | Ignition switch on (IG), shift lever position other than P or N | 9 to 14 V |
| EKN2 (B96-117) - KNK2 (B96-118) | W - B | Earth (ground) circuit of knock sensor | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK2 (B96-118) - EKN2 (B96-117) | B - W | Knock sensor signal | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A+ (B96-93) - E1 (B96-81) | W - BR | A/F sensor signal | Ignition switch on (IG) | 3.3 V*1
|
| A1A+ (B96-93) - E1 (B96-81) | W - BR | A/F sensor signal | Ignition switch on (IG) | 3.0 V*1
|
| A2A+ (B96-120) - E1 (B96-81) | L - BR | A/F sensor signal | Ignition switch on (IG) | 3.3 V*1
|
| A2A+ (B96-120) - E1 (B96-81) | L - BR | A/F sensor signal | Ignition switch on (IG) | 3.0 V*1
|
| EKNK (B96-94) - KNK1 (B96-95) | G - R | Earth (ground) circuit of knock sensor | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK1 (B96-95) - EKNK (B96-94) | R - G | Knock sensor signal | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A- (B96-116) - E1 (B96-81) | BR - BR | A/F sensor | Ignition switch on (IG) | 3.3 V*1
|
| A1A- (B96-116) - E1 (B96-81) | BR - BR | A/F sensor | Ignition switch on (IG) | 3.0 V*1
|
| A2A- (B96-119) - E1 (B96-81) | Y - BR | A/F sensor | Ignition switch on (IG) | 3.3 V*1
|
| A2A- (B96-119) - E1 (B96-81) | Y - BR | A/F sensor | Ignition switch on (IG) | 3.0 V*1
|
| P (B96-24) - E1 (B96-81) | R - BR | P shift position switch signal | Ignition switch on (IG) and shift lever P position | 9 to 14 V |
| P (B96-24) - E1 (B96-81) | R - BR | P shift position switch signal | Ignition switch on (IG) and shift lever except P position | Below 1 V |
| R (B96-25) - E1 (B96-81) | B - BR | R shift position switch signal | Ignition switch on (IG) and shift lever R position | 9 to 14 V |
| R (B96-25) - E1 (B96-81) | B - BR | R shift position switch signal | Ignition switch on (IG) and shift lever except R position | Below 1 V |
| N (B96-27) - E1 (B96-81) | L-B - BR | N shift position switch signal | Ignition switch on (IG) and shift lever N position | 9 to 14 V |
| N (B96-27) - E1 (B96-81) | L-B - BR | N shift position switch signal | Ignition switch on (IG) and shift lever except N position | Below 1 V |
| D (B96-26) - E1 (B96-81) | L - BR | D shift position switch signal | Ignition switch on (IG) and shift lever D position | 9 to 14 V |
| D (B96-26) - E1 (B96-81) | L - BR | D shift position switch signal | Ignition switch on (IG) and shift lever except D position | Below 1 V |
| 4 (A12-25) - E1 (B96-81) | P - BR | 4 shift position switch signal | Ignition switch on (IG) and shift lever S position | 9 to 14 V |
| 4 (A12-25) - E1 (B96-81) | P - BR | 4 shift position switch signal | Ignition switch on (IG) and shift lever except S position | Below 1 V |
| VCIB (B96-80) - EIB (B96-101) | LG - P | Battery current sensor | Ignition switch on (IG) | 4.5 to 5.0 V |
| IB (B96-100) - EIB (B96-101) | R - P | Battery current sensor | Ignition switch on (IG) | 0.5 to 4.5 V |
| THB (B96-103) - EIB (B96-101) | G-R - P | Battery current sensor | Ignition switch on (IG) | 0.5 to 4.5 V |
| FPR (B96-59) - E1 (B96-81) | W - BR | Fuel pump control | Cranking | 9 to 14 V |
| FPR (B96-59) - E1 (B96-81) | W - BR | Fuel pump control | Idling | 9 to 14 V |
| STA (A12-48) - E1 (B96-81) | LG - BR | Starter signal | Cranking | 9 to 14 V |
![]() |
WAVEFORM 1
Camshaft timing Oil Control Valve (OCV) operation signal
| ECM Terminal Name | Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2- |
| Tester Range | 5 V/DIV, 1 ms./DIV |
| Condition | Idling |
![]() |
WAVEFORM 2
Heated oxygen sensor signal
| ECM Terminal Name | Between OX1B and EX1B, or OX2B and EX2B |
| Tester Range | 0.2 V/DIV., 200 ms./DIV. |
| Condition | Engine speed is maintained at 2500 rpm for 2 minutes after sensor is warmed up |
![]() |
WAVEFORM 3
Fuel injector operation signal
| ECM Terminal Name | Between #10 (to 60) and E01 |
| Tester Range | 30 V/DIV., 20 ms./DIV. |
| Condition | Idling |
![]() |
WAVEFORM 4
Knock sensor signal
| ECM Terminal Name | Between KNK1 and EKNK, or KNK2 and EKN2 |
| Tester Range | 0.01 to 10 V/DIV., 0.01 to 10 ms./DIV. |
| Condition | Engine speed is maintained at 4000 rpm after engine is warmed up |
![]() |
WAVEFORM 5
Variable Valve Timing (VVT) sensor signal (a)
Crankshaft position sensor signal (b)
| ECM Terminal Name | (a) Between VV1+ and VV1- , VV2+ and VV2-, EV1+ and EV1-, or EV2+ and EV2- (b) Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
![]() |
WAVEFORM 6
Igniter IGT signal (from ECM to igniter) (a)
Igniter IGF signal (from igniter to ECM) (b)
| ECM Terminal Name | (a) Between IGT (1 to 6) and E1 (b) Between IGF1 and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
![]() |
WAVEFORM 7
Purge VSV for EVAP system operation signal
| ECM Terminal Name | Between PRG and E1 |
| Tester Range | 10 V/DIV., 50 ms./DIV. |
| Condition | Idling |
![]() |
WAVEFORM 8
Vehicle speed signal
| ECM Terminal Name | Between SPD and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Driving at 12 mph (20 km/h) |
![]() |
WAVEFORM 9
Throttle drive motor operation signal (positive terminal)
| ECM Terminal Name | Between M+ and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
![]() |
WAVEFORM 10
Throttle drive motor operation signal (negative terminal)
| ECM Terminal Name | Between M- and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
![]() |
WAVEFORM 11
Engine speed signal
| ECM Terminal Name | Between TACH and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling |
![]() |
WAVEFORM 12
CAN communication signal
| ECM Terminal Name | Between CANH and E1 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stops and ignition switch on (IG) |
![]() |
WAVEFORM 13
CAN communication signal
| ECM Terminal Name | Between CANL and E1 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stops and ignition switch on (IG) |