Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2WD)

FRONT DRIVE SHAFT ASSEMBLY (for 2WD) > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH


C127644E04
  1. for One Touch Type Clamp:
    Using a screwdriver, remove the clamp, as shown in the illustration.

  1. for Claw Engagement Type Clamp:
    Using needle-nose pliers, remove the clamp, as shown in the illustration.



2. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.



3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH


C127645E04
  1. for One Touch Type Clamp:
    Using a screwdriver, remove the clamp, as shown in the illustration.

  1. for Claw Engagement Type Clamp:
    Using needle-nose pliers, remove the clamp, as shown in the illustration.



4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.



5. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the boot from the inboard joint.



6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH


C127646E02
  1. Remove any old grease from the inboard joint.

  1. Put matchmarks on the inboard joint and outboard joint shaft.

    NOTICE:
    Do not punch the marks.

  1. Remove the inboard joint from the outboard joint shaft.



    C127648
  1. Using a snap ring expander, remove the shaft snap ring.



    C127649E01
  1. Put matchmarks on the outboard joint shaft and tripod.

    NOTICE:
    Do not punch the marks.

  1. Using a brass bar and hammer, tap off the tripod from the outboard joint shaft.

    NOTICE:
    Do not tap the rollers.

  1. Remove the inboard joint boot.



7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



8. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (for U241E)


C127651E22
  1. for One Touch Type Clamp:
    Using a screwdriver, remove the clamp, as shown in the illustration.

  1. for Claw Engagement Type Clamp:
    Using needle-nose pliers, remove the clamp, as shown in the illustration.



9. REMOVE FRONT DRIVE SHAFT DAMPER LH (for U241E)
  1. Remove the front drive shaft damper from the outboard joint shaft.



10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH


C127653
  1. Using a screwdriver, remove the outboard joint boot clamp, as shown in the illustration.



11. REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.



12. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


C127660
  1. Using a screwdriver, remove the outboard joint boot clamp, as shown in the illustration.



13. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.



14. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the outboard joint boot from the outboard joint shaft.

  1. Remove any old grease from the outboard joint.



15. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    C127655
  1. Using a screwdriver, remove the hole snap ring.



16. REMOVE FRONT DRIVE SHAFT DUST COVER LH


C127659E01
  1. Using SST and a press, press out the inboard joint from the shaft dust cover to remove the shaft dust cover.

    SST
    09950-00020  

    NOTICE:
    Be careful not to drop the inboard joint.



17. REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:
Use the same procedures described for the LH side.



18. REMOVE DRIVE SHAFT BEARING CASE


C127662
  1. Using a screwdriver, pry out the bearing case snap ring from the snap ring groove.



    C127663
  1. Using a press, press out the inboard joint from the drive shaft bearing case to remove the drive shaft bearing.

    NOTICE:
    Be careful not to drop the inboard joint.



19. REMOVE FRONT DRIVE SHAFT DUST COVER


    C127664E01
  1. Using SST and a press, press out the inboard joint from the shaft dust cover to remove the shaft dust cover.

    SST
    09950-00020  

    NOTICE:
    Be careful not to drop the inboard joint.



20. REMOVE FRONT DRIVE SHAFT BEARING


C127665
  1. Using a snap ring expander, remove the snap ring.



    C127666E01
  1. Using SST and a press, press out the inboard joint from the drive shaft bearing to remove the drive shaft bearing.

    SST
    09527-10011  

  1. Remove the bearing case snap ring from the inboard joint.