FRONT DRIVE SHAFT ASSEMBLY (for 2WD) > REASSEMBLY |
| 1. INSTALL DRIVE SHAFT BEARING CASE SUB-ASSEMBLY |
![]() |
Using SST and a press, press the drive shaft bearing case onto the inboard joint RH.
![]() |
Using a snap ring expander, install a new snap ring.
| 2. INSTALL FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST and a press, press in a new drive shaft dust cover.
| 3. INSTALL FRONT DRIVE SHAFT DUST COVER RH |
![]() |
Using SST and a press, press a new drive shaft dust cover onto the inboard joint until the distance from the tip of the inboard joint to the drive shaft dust cover onto reaches the specification, as shown in the illustration.
| 4. INSTALL FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, press in a new drive shaft dust cover onto the inboard joint.
| 5. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new hole snap ring.
| 6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT |
![]() |
Temporarily install a new outboard joint boot No. 2 clamp to the outboard joint shaft.
Install a new outboard joint boot so that it is between the outboard joint boot No. 2 clamp and outboard joint shaft.
Temporarily install a new outboard joint boot clamp to the outboard joint boot.
Pack the outboard joint shaft and boot with grease from the boot kit.
| Item | Specified Condition |
| for U241E | 190 to 200 g (6.7 to 7.1 oz.) |
| for E352 for EB61 | 205 to 215 g (7.2 to 7.6 oz.) |
| 7. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
Install a new boot clamp to the outboard joint boot and temporarily bend the lever.
![]() |
With the joint on the working surface, use your body weight to press down on the joint with one hand. Then, roll the joint forward, as shown in the illustration, and press the lever in until a "click" sound is heard.
![]() |
Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.
| 8. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH |
| 9. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH |
![]() |
Install a new boot clamp to the outboard joint boot and temporarily bend the lever.
![]() |
Using water pump pliers, temporarily lock the boot clamp by bending the lever down until a "click" sound is heard.
![]() |
Using a plastic-faced hammer, bend the tabs of the buckle to fix the lever in place. At the same time, use the plastic-faced hammer to adjust the position of the lever so that the end of the lever is aligned with the edge of the buckle.
| 10. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH |
| 11. INSTALL FRONT DRIVE SHAFT DAMPER LH (for U241E) |
![]() |
Secure the shaft in a vise between aluminum plates.
Temporarily install a new drive shaft damper clamp to the shaft, and then install the drive shaft damper so that it is between the damper clamp and the shaft.
Adjust the position of the drive shaft damper so that the distance shown in the illustration is within the specified range.
| 12. TIGHTEN FRONT DRIVE SHAFT DAMPER CLAMP LH (for U241E) |
![]() |
Secure the shaft in a vise between aluminum plates.
Tighten the drive shaft damper clamp.
for One Touch Type Clamp:
Using a screwdriver, tighten the drive shaft damper clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the drive shaft damper clamp, as shown in the illustration.
| 13. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH |
Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged
Install new parts to the outboard joint shaft in the following order.
Inboard joint boot clamp
No. 2 inboard joint boot clamp
Inboard joint clamp
![]() |
Place the tripod so that the beveled side of the tripod axial spline faces toward the outboard joint.
Align the matchmarks placed before removal.
Using a brass bar and hammer, tap the tripod onto the shaft.
Pack the inboard joint shaft and boot with grease from the boot kit.
![]() |
Using a snap ring expander, install a new shaft snap ring.
Align the matchmarks, and install the inboard joint to the outboard joint shaft.
| 14. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH |
| 15. INSTALL FRONT AXLE INBOARD JOINT BOOT |
Install the boot to the inboard joint.
| 16. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, tighten the clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the clamp, as shown in the illustration.
| 17. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP RH |
| 18. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, tighten the clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the clamp, as shown in the illustration.
| 19. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH |
| 20. INSPECT FRONT DRIVE SHAFT |
![]() |
Secure the shaft in a vise between aluminum plates.
Check that there is no severe play in the radial direction of the outboard joint.
Check that the inboard joint slides smoothly in the thrust direction.
Check that there is no severe play in the radial direction of the inboard joint.
Check the boots for damage.
![]() |
Measure length (A) of the drive shaft.
| Item | Drive shaft LH (Dimension) | Drive shaft RH (Dimension) |
| for U241E | 585.2 mm (1.92 ft.) | 902.0 mm (2.96 ft.) |
| for E352 | 583.6 mm (1.91 ft.) | 906.4 mm (2.97 ft.) |
| for EB61 | 594.6 mm (1.95 ft.) | 893.4 mm (2.93 ft.) |