FRONT DRIVE SHAFT ASSEMBLY (for 4WD) > REASSEMBLY |
| 1. INSTALL FRONT DRIVE SHAFT BEARING |
![]() |
Install a new snap ring to the inboard shaft.
Using SST and a press, press the drive shaft bearing onto the inboard joint RH.
![]() |
Using a snap ring expander, install a new snap ring.
| 2. INSTALL FRONT DRIVE SHAFT DUST COVER RH |
![]() |
Using SST and a press, press a new drive shaft dust cover onto the inboard joint until the distance shown in the illustration reaches the specification.
| 3. INSTALL FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, press a new drive shaft dust cover onto the inboard joint.
| 4. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new hole snap ring.
| 5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT |
![]() |
Temporarily install a new outboard joint boot No. 2 clamp to the outboard joint shaft.
Install a new outboard joint boot so that it is between the outboard joint boot No. 2 clamp and outboard joint shaft.
Temporarily install a new outboard joint boot clamp to the outboard joint boot.
Pack the outboard joint shaft and boot with grease from the boot kit.
| Item | Specified Condition |
| 1AZ-FE, 2AZ-FE for U140F 3ZR-FAE for K111F | 190 to 200 g (6.7 to 7.1 oz.) |
| 1AZ-FE, 2AZ-FE for E352F/E359F 2GR-FE 3ZR-FAE for EB61F | 205 to 215 g (7.2 to 7.6 oz.) |
| 6. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
Install a new boot clamp to the outboard joint boot and temporarily bend the lever.
![]() |
With the joint on the working surface, use your body weight to press down on the joint with one hand. Then, roll the joint forward, as shown in the illustration, and press the lever in until a "click" sound is heard.
![]() |
Using a plastic-faced hammer, bend the tabs of the buckle to fix the lever in place. At the same time, use the plastic-faced hammer to adjust the position of the lever so that the end of the lever is aligned with the edge of the buckle.
| 7. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH |
| 8. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH |
![]() |
Install a new boot clamp to the outboard joint boot and temporarily bend the lever.
![]() |
Using water pump pliers, temporarily lock the boot clamp by bending the lever down until a "click" sound is heard.
![]() |
Using a plastic-faced hammer, bend the tabs of the buckle to fix the lever in place. At the same time, use the plastic-faced hammer to adjust the position of the lever so that the end of the lever is aligned with the edge of the buckle.
| 9. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH |
| 10. INSTALL FRONT DRIVE SHAFT DAMPER LH (except E352F/E359F, EB61F) |
![]() |
Secure the shaft in a vise between aluminum plates.
Temporarily install a new drive shaft damper clamp to the shaft, and then install the drive shaft damper so that it is between the damper clamp and the shaft.
Adjust the position of the drive shaft damper so that the distance shown in the illustration is within the specified range.
| 11. TIGHTEN FRONT DRIVE SHAFT DAMPER CLAMP |
![]() |
Secure the shaft in a vise between aluminum plates.
Tighten the drive shaft damper clamp.
for One Touch Type Clamp:
Using a screwdriver, tighten the drive shaft damper clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the drive shaft damper clamp, as shown in the illustration.
| 12. INSTALL FRONT DRIVE SHAFT DAMPER |
![]() |
Secure the shaft in a vise between aluminum plates.
Temporarily install a new drive shaft damper clamp to the shaft, and then install the drive shaft damper so that it is between the damper clamp and the shaft.
Adjust the position of the drive shaft damper so that the distance shown in the illustration is within the specified range.
| 13. TIGHTEN FRONT DRIVE SHAFT DAMPER CLAMP |
| 14. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH |
Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.
Install new parts to the outboard joint shaft in the following order.
Inboard joint boot clamp
No. 2 inboard joint boot clamp
Inboard joint boot
![]() |
Place the beveled side of the tripod axial spline toward the outboard joint.
Align the matchmarks placed before removal.
Using a brass bar and hammer, tap the tripod onto the shaft.
Pack the inboard joint shaft and boot with grease from the boot kit.
![]() |
Using a snap ring expander, install a new shaft snap ring.
Align the matchmarks, and install the inboard joint to the outboard joint shaft.
| 15. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH |
| 16. INSTALL FRONT AXLE INBOARD JOINT BOOT |
Install the inboard joint boot to the inboard joint.
| 17. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, tighten the inboard joint boot clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the inboard joint boot clamp, as shown in the illustration.
| 18. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP RH |
| 19. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, tighten the No. 2 inboard joint boot clamp, as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, tighten the No. 2 inboard joint boot clamp, as shown in the illustration.
| 20. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH |
| 21. INSPECT FRONT DRIVE SHAFT |
![]() |
Secure the shaft in a vise between aluminum plates.
Check that there is no severe play in the radial direction of the outboard joint.
Check that the inboard joint slides smoothly in the thrust direction.
Check that there is no severe play in the radial direction of the inboard joint.
Check the boots for damage.
![]() |
Measure length (A) of the drive shaft.
| Item | Drive shaft LH (Dimension) | Drive shaft RH (Dimension) |
| 1AZ-FE, 2AZ-FE for U140F | 572.5 mm (1.88 ft.) | 918 mm (3.01 ft.) |
| 1AZ-FE, 2AZ-FE for E352E/E359 | 583.6 mm (1.91 ft.) | 909.4 mm (2.98 ft.) |
| 2GR-FE | 570.9 mm (1.87 ft.) | 922.4 mm (3.03 ft.) |
| 3ZR-FAE for EB61F | 594.6 mm (1.95 ft.) | 896.4 mm (2.94 ft.) |
| 3ZR-FAE for K111F | 591.2 mm (1.94 ft.) | 881.9 mm (2.89 ft.) |