Home › DRIVE LINE › DRIVE SHAFT › REAR DRIVE SHAFT ASSEMBLY

REAR DRIVE SHAFT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. DRAIN DIFFERENTIAL OIL


    C109019
  1. Using a 10 mm socket hexagon wrench, remove the rear differential drain plug and gasket, and drain the oil.

  1. Install a new gasket to the rear differential drain plug.

  1. Using a 10 mm socket hexagon wrench, install the rear differential drain plug and gasket.



3. REMOVE REAR WHEEL


4. REMOVE TAILPIPE ASSEMBLY
  1. Remove the tailpipe for 1AZ-FE .

  1. Remove the tailpipe for 2AZ-FE .

  1. Remove the tailpipe for 3ZR-FAE .

  1. Remove the tailpipe for 2GR-FE .



5. REMOVE NO. 2 EXHAUST PIPE SUB-ASSEMBLY
  1. Remove the No. 2 exhaust pipe sub-assembly for 2GR-FE .



6. REMOVE EXHAUST CENTER PIPE ASSEMBLY
  1. Remove the center pipe for 1AZ-FE .

  1. Remove the center pipe for 2AZ-FE .

  1. Remove the center pipe for 3ZR-FAE .

  1. Remove the center pipe for 2GR-FE .



7. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front pipe for 1AZ-FE .

  1. Remove the front pipe for 2AZ-FE .

  1. Remove the front pipe for 3ZR-FAE .

  1. Remove the front pipe for 2GR-FE .



8. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    C127524
  1. Remove the 2 bolts and 2 adjusting washers, and disconnect the propeller with center bearing shaft.

    NOTICE:
    1. During the removal, do not exert excessive force on the universal joint.
    2. When removing, transporting or storing the propeller with center bearing shaft assembly, do not allow the No. 2 joint angle to exceed 20°.



    C127525E01
  1. Place matchmarks on the differential carrier and propeller shaft.

  1. Remove the 4 nuts and 4 washers, and disconnect the propeller shaft and differential carrier.



    C127526E01
  1. Place matchmarks on the transfer and propeller shaft.

  1. Remove the 4 nuts and 4 washers, and disconnect the propeller shaft from the transfer.



9. REMOVE REAR AXLE SHAFT NUT


    C129486E01
  1. Using SST and hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brake, remove the lock axle hub nut.



10. DISCONNECT DIFFERENTIAL CARRIER ASSEMBLY


C129479E01
  1. Support the rear differential carrier with a transmission jack or equivalent.

  1. Fix the nuts in place and remove the 2 bolts A and bolt B.

    NOTICE:
    Do not loosen the nuts. Loosen the bolts.



    C129480
  1. Slowly lower the jack and then tilt the rear differential carrier as shown in the illustration.



    C129481
  1. Set the tip of the tire lever to the position on the rear drive shaft inboard joint shown in the illustration. Then, using the ribbed part of the rear differential carrier as a fulcrum, disconnect the left and right rear drive shafts.

    NOTICE:
    Do not scratch the rear drive shaft dust cover.



11. DISCONNECT REAR SPEED SENSOR LH
  1. Disconnect the speed sensor .



12. REMOVE REAR DRIVE SHAFT ASSEMBLY LH


C129489E01
  1. Put matchmarks on the drive shaft and the axle hub.

    NOTICE:
    Do not punch the marks.

  1. Using a plastic-faced hammer, separate the drive shaft from the axle hub.

    NOTICE:
    Be careful not to damage the boot and speed sensor rotor. Do not excessively push out the drive shaft from the axle.