DIFFERENTIAL CARRIER OIL SEAL > INSTALLATION |
| 1. INSTALL DIAPHRAGM OIL SEAL |
Apply a light coat of MP grease No. 2 to the lip of a new diaphragm oil seal.
![]() |
Using SST and a hammer, tap the diaphragm oil seal into the rear differential carrier according to the specification.
| 2. INSTALL TRANSMISSION COUPLING SHIM |
![]() |
Measure each of the dimensions.
Select a transmission coupling shim based on the difference between dimensions A and B, and install the shim.
| Difference of dimension A and B mm (in.) | Thickness mm (in.) | Identifying Mark |
| 3.96 to 4.01 (0.148 to 0.154) | 1.98 to 2.02 (0.078 to 0.080) | 1 |
| 4.26 to 4.31 (0.161 to 0.168) | 2.28 to 2.32 (0.090 to 0.091) | 2 |
| 4.56 to 4.61 (0.174 to 0.181) | 2.58 to 2.62 (0.102 to 0.103) | 3 |
| 3.81 to 3.86 (0.141 to 0.148) | 1.83 to 1.87 (0.072 to 0.074) | 4 |
| 4.11 to 4.16 (0.154 to 0.161) | 2.13 to 2.17 (0.084 to 0.085) | 5 |
| 4.41 to 4.46 (0.168 to 0.174) | 2.43 to 2.47 (0.096 to 0.097) | 6 |
| 3.71 to 3.76 (0.146 to 0.148) | 1.73 to 1.77 (0.068 to 0.070) | 8 |
| 3.76 to 3.81 (0.148 to 0.150) | 1.78 to 1.82 (0.070 to 0.072) | 9 |
| 3.86 to 3.91 (0.151 to 0.154) | 1.88 to 1.92 (0.074 to 0.076) | 10 |
| 3.91 to 3.96 (0.154 to 0.156) | 1.93 to 1.97 (0.076 to 0.078) | 11 |
| 4.01 to 4.06 (0.158 to 0.160) | 2.03 to 2.07 (0.080 to 0.081) | 12 |
| 4.06 to 4.11 (0.160 to 0.162) | 2.08 to 2.12 (0.082 to 0.083) | 13 |
| 4.16 to 4.21 (0.164 to 0.166) | 2.18 to 2.22 (0.086 to 0.087) | 14 |
| 4.21 to 4.26 (0.166 to 0.168) | 2.23 to 2.27 (0.088 to 0.089) | 15 |
| 4.31 to 4.36 (0.170 to 0.172) | 2.33 to 2.37 (0.092 to 0.093) | 16 |
| 4.36 to 4.41 (0.172 to 0.174) | 2.38 to 2.42 (0.094 to 0.095) | 17 |
| 4.46 to 4.51 (0.176 to 0.178) | 2.48 to 2.52 (0.098 to 0.099) | 18 |
| 4.51 to 4.56 (0.178 to 0.180) | 2.53 to 2.57 (0.100 to 0.101) | 19 |
| 4.61 to 4.66 (0.181 to 0.183) | 2.63 to 2.67 (0.104 to 0.105) | 20 |
| 4.66 to 4.71 (0.183 to 0.185) | 2.68 to 2.72 (0.106 to 0.107) | 21 |
| 3. INSTALL TRANSMISSION COUPLING CONICAL SPRING WASHER |
![]() |
Install the transmission coupling conical spring washer to the rear differential carrier.
| 4. INSTALL YOKE |
Using a 5 mm socket hexagon wrench, install the yoke with the 3 bolts.
| 5. INSTALL 4WD LINEAR SOLENOID |
Install a new O-ring to the solenoid.
Install the solenoid to the yoke.
Install the snap ring.
| 6. INSTALL ELECTROMAGNETIC COUPLING |
Using white gasoline, remove grease and oil from the alignment surfaces of the rear differential carrier and transmission coupling.
![]() |
Apply seal packing to the areas indicated in the illustration of the transmission coupling.
![]() |
Install the rear differential carrier cover to the rear differential carrier assembly with the 4 bolts.
| 7. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
Install the propeller shaft (Click here).
| 8. ADD DIFFERENTIAL OIL |
Stop the vehicle on a level surface.
![]() |
Using a 10 mm socket hexagon wrench, remove the rear differential filler plug and gasket.
![]() |
Check that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
Using a 10 mm socket hexagon wrench, install a new gasket and the rear differential filler plug.