Home › BODY › SEAT › REAR NO. 1 SEAT ASSEMBLY (for RH Side)

REAR NO. 1 SEAT ASSEMBLY (for RH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR SEATBACK COVER RH


    B131934
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.



2. INSTALL REAR SEAT COVER


    B131935
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.



3. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B135787E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.



    B060977E01
  1. Attach the 4 claws to install the 2 headrest supports.



    B131930E01
  1. Lift up the seatback cover and install the 13 hog rings.



4. INSTALL REAR SEATBACK PROTECTOR


    B140208
  1. Install the protector with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the clip.



    B131929E01
  1. Attach the 2 clips and close the fastening tape.



5. INSTALL REAR NO. 1 SEATBACK ASSEMBLY RH


    B140191
  1. Install the seatback with the 5 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B140189
  1. Attach the 2 clamps and connect the cable to the reclining adjuster.



6. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH


    B131927
  1. Attach the 2 claws to install the lever base.

  1. Install the screw.



7. INSTALL REAR SEAT RECLINING RELEASE LEVER


    B140197
  1. Attach the claw to install the release lever.



    B140193
  1. Install the cover with the 2 screws.



8. INSTALL REAR SEAT CUSHION REAR MOULDING RH


    B131539
  1. Attach the 2 claws to install the moulding.

  1. Install the screw.



9. INSTALL REAR SEAT CUSHION MOULDING RH

HINT:
Use the same procedures described for the rear seat cushion rear moulding RH.



10. INSTALL REAR SEAT REAR BRACKET COVER RH


    B131540
  1. Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.

  1. Install the 2 screws.



11. INSTALL REAR NO. 1 SEAT CUSHION COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B135822E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.



    B131538E01
  1. Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 18 new hog rings.



    B140186
  1. Attach the 2 hooks.



12. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B131542
  1. Install the cushion with the 2 bushes and 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    B140185E01
  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the rubber band of the seatback cover to the seat cushion frame.



13. INSTALL REAR SEAT INNER BELT ASSEMBLY RH


B138223
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



14. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER


    B131541
  1. Attach the 5 claws to install the hinge cover.



15. INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

HINT:
Use the same procedures described for the rear No. 2 seat cushion hinge cover.



16. INSTALL REAR SEAT HEADREST ASSEMBLY