Home › ENGINE ยท 2GR-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A132448E02
  1. Install a new water pump gasket and the water pump with the 16 bolts.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt B and C:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    NOTICE:
    1. Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive.
      Adhesive:
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    2. Make sure that there is no oil on the threads of bolts A.



2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A138913E01
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

    HINT:
    Each bolt length is as follows:
    A: 70 mm (2.76 in.)
    B: 30 mm (1.18 in.)

  1. Install the V-ribbed belt tensioner by tightening bolt 1 and bolt 2 in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



3. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A132445
  1. Install the No. 2 idler pulley cover plate and No. 2 idler pulley with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL WATER PUMP PULLEY


    A132444E01
  1. Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



5. INSTALL CRANKSHAFT PULLEY


    A132068E01
  1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.

  1. Using SST, install the pulley bolt.

    SST
    09213-70011   (09213-70020)
    09330-00021  

    Torque:
    250 N*m{ 2549 kgf*cm , 184 ft.*lbf }



6. INSTALL WATER INLET HOUSING


    A132443
  1. Install a new water inlet housing No. 1 gasket and water outlet pipe O-ring.



    A132442
  1. Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful not to allow the O-ring to get caught between the parts.

  1. Connect the water hose.



7. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    A136828E01
  1. Install the front No. 1 engine mounting bracket LH with the 6 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    1. Install the water inlet housing and mounting bracket within 15 minutes after installing the chain cover.
    2. Do not start the engine for at least 2 hours after installation.



8. INSTALL ENGINE ASSEMBLY
  1. Install the engine (Click here).