THERMOSTAT > INSTALLATION |
| 1. INSTALL THERMOSTAT |
Install a new gasket to the thermostat.
![]() |
Install the thermostat with the jiggle valve facing upward.
| 2. INSTALL WATER INLET |
![]() |
Install the water inlet with the 2 nuts.
| 3. CONNECT NO. 1 RADIATOR HOSE |
| 4. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Install the No. 2 idler pulley cover plate and No. 2 idler pulley with the bolt.
| 5. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
![]() |
Install the front No. 1 engine mounting bracket LH with the 6 bolts.
| 6. INSTALL ENGINE MOUNTING INSULATOR RH |
![]() |
Install the engine mounting insulator RH with the 2 nuts and 5 bolts.
| 7. INSTALL FAN AND GENERATOR V BELT |
![]() |
Rotate the tensioner pulley counterclockwise, and then install the V-ribbed belt.
![]() |
If it is difficult to install the V-ribbed belt, perform the following procedure.
Put the V-ribbed belt on everything except the tensioner pulley as shown in the illustration.
While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.
| 8. CONNECT RADIATOR RESERVOIR TANK |
![]() |
Connect the radiator reservoir tank with the 2 bolts.
| 9. INSTALL RADIATOR SUPPORT OPENING COVER |
![]() |
Install the cover with the 9 clips.
| 10. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 3 clips to install the engine cover.
| 11. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
![]() |
Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates. While the cooling fan operates, circulate the coolant for several minutes.
Set the air conditioning as follows while warming up the engine.
| Item | Specified Condition |
| Manual Air Conditioning System | Fan speed: Any setting except OFF |
| Temperature: Toward WARM Air conditioning switch: OFF | |
| Automatic Air Conditioning System | Temperature: Toward MAX Air conditioning switch: OFF |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Squeeze the No. 1 and No. 2 radiator hoses several times to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 12. INSPECT FOR COOLANT LEAK |
Remove the radiator reservoir cap.
![]() |
Fill the radiator with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator cap.
| 13. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH |
![]() |
Install the reinforcement with the 4 bolts.
| 14. INSTALL ENGINE UNDER COVER REAR RH |
Install the under cover with the 2 clips.
| 15. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 2 bolts, 4 screw and 12 clips.
| 16. INSTALL FRONT WHEEL RH |