DTC B1643/81 Driver Side Satellite Sensor Bus Initialization Incomplete |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1643/81 | When one of following conditions is met:
|
|

| 1.CHECK FOR DTC |
![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, driver side rear airbag sensor and the driver side - side airbag sensor.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor and the driver side - side airbag sensor.
for LHD:
Using a service wire, connect K30-4 (BBL+) and K30-3 (BBL-) of connector C.
for RHD:
Using a service wire, connect L21-4 (BBR+) and L21-3 (BBR-) of connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K1-8 (BBD+) - K1-15 (BBD-) | Below 1 Ω |
| Tester Connection | Specified Condition |
| L18-8 (BBD+) - L18-15 (BBD-) | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K1-8 (BBD+) - K1-15 (BBD-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L18-8 (BBD+) - L18-15 (BBD-) | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| K1-8 (BBD+) - Body ground | Below 1 V |
| K1-15 (BBD-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| L18-8 (BBD+) - Body ground | Below 1 V |
| L18-15 (BBD-) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K1-8 (BBD+) - Body ground | 1 MΩ or higher |
| K1-15 (BBD-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L18-8 (BBD+) - Body ground | 1 MΩ or higher |
| L18-15 (BBD-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (OPEN) |

Disconnect the connectors from the driver side - side airbag sensor and the driver side rear airbag sensor.
for LHD:
Using a service wire, connect K31-1 (BCL-) and K31-2 (BCL+) of connector C.
for RHD:
Using a service wire, connect L22-1 (BCR-) and L22-2 (BCR+) of connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K30-1 (BCL+) - K30-2 (BCL-) | Below 1 Ω |
| Tester Connection | Specified Condition |
| L21-1 (BCR+) - L21-2 (BCR-) | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K30-1 (BCL+) - K30-2 (BCL-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L21-1 (BCR+) - L21-2 (BCR-) | 1 MΩ or higher |
|
| ||||
| OK | |
| 9.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| K30-1 (BCL+) - Body ground | Below 1 V |
| K30-2 (BCL-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| L21-1 (BCR+) - Body ground | Below 1 V |
| L21-2 (BCR-) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 10.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K30-1 (BCL+) - Body ground | 1 MΩ or higher |
| K30-2 (BCL-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L21-1 (BCR+) - Body ground | 1 MΩ or higher |
| L21-1 (BCR-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 11.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
![]() |
Connect the connectors to the center airbag sensor.
Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1643/81 is output | B |
| DTC B1648/82 is output | C |
|
| ||||
|
| ||||
| A | |
| 12.CHECK DRIVER SIDE REAR AIRBAG SENSOR |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the driver side rear airbag sensor with the front passenger side rear airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1643/81 is output | B |
| DTC B1648/82 is output | C |
|
| ||||
|
| ||||
| A | ||
| ||