THROTTLE BODY > INSTALLATION |
| 1. INSTALL THROTTLE BODY ASSEMBLY |
Install a new gasket into the intake manifold.
![]() |
Install the throttle body with the 2 bolts and 2 nuts.
![]() |
Connect the throttle body connector and 2 water hoses.
| 2. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Insert the hinge part of the air cleaner cap and hose into the air cleaner case, and then fasten the 2 hook clamps.
![]() |
Connect the No. 1 air cleaner hose to the throttle body and push apart the tabs of the No. 1 air cleaner hose clamp.
Connect the No. 2 ventilation hose to the cylinder head cover.
![]() |
Attach the clamp.
Connect the mass air flow meter connector.
| 3. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Attach the 4 clips to install the cover.
| 4. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening until it is filled to the B line at the base of the reservoir filler neck.
| Item | Specified Condition |
| for Manual Transaxle | 5.8 liters (6.1 US qts, 5.1 Imp. qts) |
| for CVT | 6.0 liters (6.3 US qts, 5.3 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Condition |
| Manual Air Conditioning System | Fan speed: Any setting except off Temperature: Toward WARM Air conditioning switch: Off |
| Automatic Air Conditioning System | Temperature: Toward MAX (HOT) Air conditioning switch: Off |
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 5. INSPECT FOR COOLANT LEAK |
Remove the radiator reservoir cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator reservoir cap.
| 6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 7. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the under cover with the 6 screws and 10 clips.
| 8. PERFORM INITIALIZATION |
Disconnect the EFI MAIN and ETCS fuses at the same time. Wait at least 60 seconds, and then reconnect the fuses.
Turn the ignition switch to ON without operating the accelerator pedal.
Connect the intelligent tester to the DLC3 and clear the DTCs (Click here).
Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.
| Item | Specified Condition |
| for Manual Transaxle | 580 to 680 rpm |
| for CVT | 600 to 700 rpm |
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.
Perform a road test and confirm that there are no abnormalities.