Home › ENGINE ยท 3ZR-FAE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here



1. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.



  1. Using an E8 "TORX" socket wrench, install the stud bolts.


    A150960E07

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }



2. INSTALL SPARK PLUG TUBE

NOTICE:
A211988E06
When using a new cylinder head, the spark plug tubes must be replaced.

  1. Apply adhesive onto the shaded area of a new spark plug tube.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

    Standard application width:
    1.0 to 3.0 mm (0.0394 to 0.118 in.)

    Distance:
    1.0 to 7.0 mm (0.0394 to 0.294 in.)

    NOTICE:
    1. Install the spark plug tube within 3 minutes after applying adhesive.
    2. Be careful not to deform the spark plug tube.
    3. Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.



    A205906E02
  1. Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

    Standard protrusion height:
    122 mm (4.80 in.)

    NOTICE:
    To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



3. INSTALL NO. 2 STRAIGHT SCREW PLUG

NOTICE:
A150950
If water leaks from the straight screw plug or the plug is corroded, replace it.

  1. Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



4. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head.



5. INSTALL VALVE STEM OIL SEAL


    A146313E02
  1. Apply a light coat of engine oil to a new oil seal.

    NOTICE:
    Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal to the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve oil seal is gray and the exhaust valve oil seal is black.



    A150956E01
  1. Using SST, push on the oil seal.

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.



6. INSTALL INTAKE VALVE


    A094935E15
  1. Place the cylinder head on wooden blocks.

  1. Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip, as shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A150946E02
  1. Using SST, compress the compression spring and install the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    A150974
  1. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    1. Be careful not to damage the valve stem tip.
    2. Be careful not to damage the retainer.



7. INSTALL EXHAUST VALVE


    A094936E14
  1. Place the cylinder head on wooden blocks.

  1. Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip, as shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A150947E02
  1. Using SST, compress the compression spring and install the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    A150973
  1. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    1. Be careful not to damage the valve stem tip.
    2. Be careful not to damage the retainer.