ENGINE UNIT > REASSEMBLY |
| 1. INSTALL STIFFENING CRANKCASE RING PIN |
![]() |
Using a plastic-faced hammer, tap in 2 new ring pins until they stop.
| Item | Protrusion Height | Height | Width |
| Ring Pin | 3.0 mm (0.118 in.) | 11 mm (0.433 in.) | 8 mm (0.315 in.) |
| 2. INSTALL STIFFENING CRANKCASE STUD BOLT |
![]() |
Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.
| 3. INSTALL STIFFENING CRANKCASE ASSEMBLY |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| Area | Specified Condition |
| Continuous Line | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| A | 4.5 to 5.5 mm (0.177 to 0.217 in.) |
![]() |
Install the stiffening crankcase with the 11 bolts in the sequence shown in the illustration.
| Item | Specified Condition |
| Bolt A | 138 mm (5.43 in.) |
| Bolt B | 35 mm (1.38 in.) |
| Bolt C | 70 mm (2.76 in.) |
Recheck the torque for bolts 1 and 2.
Wipe off any excess seal packing with a clean piece of cloth.
| 4. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install the oil pump with the 3 bolts.
| 5. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
Apply seal packing in a continuous line as shown in the illustration.
| Area | Seal Packing Diameter | Distance from Center of Bolt Hole to Center of Seal Packing |
| A - A | 3.0 to 4.5 mm (0.118 to 0.177 in.) | 6.0 mm (0.236 in.) |
| B - B | - |
![]() |
Install the No. 2 oil pan with the 10 bolts and 2 nuts.
| 6. INSTALL OIL PAN DRAIN PLUG |
![]() |
Install a new gasket and the drain plug.
| 7. INSTALL ENGINE REAR OIL SEAL |
![]() |
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.
| 8. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Apply adhesive to the threads of the drain cock.
| *1 | Adhesive |
![]() |
Install the drain cock as shown in the illustration.
Install the drain cock plug to the drain cock.
| 9. INSTALL NO. 1 TAPER SCREW PLUG |
![]() |
Apply adhesive to 2 or 3 threads of the taper screw plug.
| *1 | Adhesive |
![]() |
Install the taper screw plug.
| 10. INSTALL VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the ventilation valve sub-assembly.
| *1 | Adhesive |
![]() |
Using a 22 mm ball joint lock nut wrench, install the ventilation valve sub-assembly.
| 11. INSTALL CYLINDER HEAD GASKET |
![]() |
Apply seal packing to the cylinder block as shown in the illustration.
| Area | Seal Packing Application Length | Distance from Edge of Cylinder Block to Center of Seal Packing |
| A | - | 2.0 to 4.0 mm (0.0787 to 0.157 in.) |
| B | 10 to 15 mm (0.394 to 0.591 in.) | - |
![]() |
Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
![]() |
Apply seal packing to the cylinder head gasket as shown in the illustration.
| Area | Seal Packing Application Length | Distance from Edge of Cylinder Head Gasket to Center of Seal Packing |
| A | - | 2.0 to 4.0 mm (0.0787 to 0.157 in.) |
| B | 10 to 15 mm (0.394 to 0.591 in.) | - |
| 12. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder block.
Install the plate washers to the cylinder head bolts.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Step 1:
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.
![]() |
Step 2:
Mark each cylinder head bolt head with paint as shown in the illustration.
Tighten the cylinder head bolts 90° in the sequence shown in step 1.
Step 3:
Tighten the cylinder head bolts another 45° in the sequence shown in step 1.
Check that the paint mark is now at a 135° angle to the front.
![]() |
After tightening the cylinder head bolts, wipe off the seal packing material that has seeped out from between the contact surfaces of the cylinder head and cylinder block.
| 13. INSTALL VALVE STEM CAP |
Apply a light coat of engine oil to the valve stem ends.
Install the 16 valve stem caps to the cylinder head.
| 14. INSTALL VALVE LASH ADJUSTER ASSEMBLY |
Inspect each valve lash adjuster before installing it .
Install the 16 valve lash adjusters to the cylinder head.
| 15. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Apply engine oil to the valve lash adjuster tips and valve stem cap ends.
Make sure that the No. 1 valve rocker arms are installed as shown in the illustration.
| *1 | Lash Adjuster |
| *2 | Valve Rocker Arm |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
| 16. INSTALL CAMSHAFT HOUSING STRAIGHT PIN |
![]() |
Using a plastic-faced hammer, tap in a new straight pin to the specified protrusion height.
| Item | Protrusion Height | Height | Width |
| Straight Pin | 6.5 to 7.5 mm (0.256 to 0.295 in.) | 14 mm (0.551 in.) | 6.0 mm (0.236 in.) |
| 17. INSTALL CAMSHAFT HOUSING STUD BOLT |
![]() |
Using an E7 "TORX" socket wrench, install the camshaft housing stud bolts.
| 18. INSTALL CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY |
![]() |
Install a new O-ring to the continuously variable valve lift controller.
| *1 | Protrusion |
![]() |
Install the control actuator clip to the control actuator connector.
![]() |
Install the control actuator connector to the valve rocker shaft and rotate the control actuator connector as shown in the illustration.
Insert the continuously variable valve lift controller into the camshaft housing.
![]() |
Install the continuously variable valve lift controller to the camshaft housing with the bolt.
![]() |
Using a screwdriver, slide the control actuator clip from the control actuator connector.
Slide only the upper part of the control actuator clip as the straight pin may fall if the control actuator clip is completely removed.
![]() |
Using a screwdriver, lightly pry the control actuator connector and align the hole in the control actuator connector with the hole in the continuously variable valve lift controller.
| *1 | Rocker Shaft |
| *2 | Clip |
| *3 | Straight Pin Hole |
| *4 | Connector |
| *5 | Controller Shaft |
![]() |
Insert the straight pin into the control actuator connector.
Using a screwdriver, install the control actuator clip to the control actuator connector.
| 19. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY |
![]() |
Check that the valve rocker arms are installed as shown in the illustration.
| *1 | Valve Stem Cap |
| *2 | Valve Rocker Arm |
| *3 | Valve Lash Adjuster |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| Area | Specified Condition |
| Continuous Line | 3.5 to 4.5 mm (0.138 to 0.177 in.) |
| A | 8.0 mm (0.315 in.) |
| B | 7.0 mm (0.276 in.) |
![]() |
Set the camshaft and No. 2 camshaft as shown in the illustration.
Install the camshaft housing with the 17 bolts and tighten them in the order shown in the illustration.
| 20. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
![]() |
Put the camshaft timing exhaust gear and camshaft together by aligning the pin hole and straight pin.
| *1 | Straight Pin |
| *2 | Pin Hole |
Lightly press the gear against the camshaft and turn the gear. Push further at the position where the pin enters the hole.
![]() |
Check that there is no clearance between the gear and camshaft flange.
![]() |
Tighten the flange bolt with the camshaft timing exhaust gear secured in place.
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear is locked.
| 21. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned as shown in the illustration.
| *1 | Straight Pin |
| *2 | Key Groove |
![]() |
Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.
| *1 | Straight Pin |
| *2 | Key Groove |
![]() |
Check that there is no clearance between the camshaft timing gear and camshaft flange.
![]() |
Tighten the flange bolt with the camshaft timing gear secured in place.
![]() |
Check that the camshaft timing gear can move in the retard direction (clockwise) and is locked in the most retarded position.
| *1 | Lock |
| 22. INSTALL CRANKSHAFT TIMING GEAR KEY |
![]() |
Using a plastic-faced hammer, tap in the 2 crankshaft timing gear keys.
| 23. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
![]() |
Install the crankshaft position sensor plate with the "F" mark facing forward.
| 24. INSTALL NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Temporarily install the crankshaft pulley bolt.
Set the crankshaft key as shown in the illustration.
Turn the drive shaft so that the cutout faces upward.
Remove the crankshaft pulley bolt.
![]() |
Align the yellow mark plates with the timing mark of each gear as shown in the illustration.
Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.
Temporarily install the oil pump drive shaft gear with the nut.
![]() |
Install the spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.
![]() |
Temporarily install the crankshaft pulley with the pulley bolt.
Using SST, hold the crankshaft. Then tighten the drive shaft gear nut.
Remove SST, the crankshaft pulley bolt and crankshaft pulley.
| 25. INSTALL CRANKSHAFT TIMING SPROCKET |
![]() |
Install the crankshaft timing sprocket as shown in the illustration.
| 26. INSTALL NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper with the 2 bolts.
| 27. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
![]() |
Temporarily install the crankshaft pulley bolt.
Turn the crankshaft counterclockwise to position the timing gear key at the top.
| *1 | Timing Gear Key |
![]() |
Check that the timing marks on the camshaft timing gears are aligned as shown in the illustration.
| *1 | Timing Mark |
Remove the crankshaft pulley bolt.
| 28. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain.
| *1 | Mark Plate (Orange) |
| *2 | Timing Mark |
Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain.
Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear clockwise.
![]() |
Align the mark plates (yellow) and timing marks and install the chain to the crankshaft timing gear.
| *1 | Timing Mark |
| *2 | Mark Plate (Yellow) |
| 29. INSTALL CHAIN TENSIONER SLIPPER |
![]() |
Install the chain tensioner slipper to the cylinder block.
| 30. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION |
Check each timing mark at TDC/compression.

| *1 | Timing Mark | *2 | Mark Plate (Orange) |
| *3 | Mark Plate (Yellow) | - |
| 31. INSTALL NO. 1 GENERATOR BRACKET |
![]() |
Install the generator bracket with the 4 bolts.
| 32. INSTALL WATER INLET HOUSING STUD BOLT |
![]() |
Using an E5 "TORX" socket wrench, install the stud bolts as shown in the illustration.
| 33. INSTALL WATER INLET HOUSING |
![]() |
Install a new gasket and the water inlet housing with the 3 bolts.
| 34. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Install a new gasket.
![]() |
for Type A:
Install the water pump with the 3 bolts.
![]() |
for Type B:
Install the water pump with the 3 bolts.
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head, camshaft housing, stiffening crankcase and cylinder block.

![]() |
Install 3 new O-rings.
Apply seal packing as shown in the illustration.

Apply seal packing to the timing chain cover in a continuous line as shown in the following illustration.

| Item | Seal Packing |
| Dashed line | Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent |
| Continuous line | |
| Alternate long and short dashed line | Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent |
| Area | Seal Packing Diameter | Distance from Edge of Cover to: | Seal Packing Application Length | Distance from Top of Cover to Top of Seal Packing |
| Dashed line | 2.5 to 3.0 mm (0.0984 to 0.118 in.) | Center of seal packing 2.5 mm (0.0984 in.) | - | - |
| Continuous line | 4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.) | - | - | - |
| Alternate long and short dashed line | 4.0 mm (0.157 in.) | Center of seal packing 3.0 mm (0.118 in.) | - | - |
| A - A | 2.5 to 3.0 mm (0.0984 to 0.118 in.) | Center of seal packing 2.5 mm (0.0984 in.) | - | - |
| B - B | 4.5 to 5.5 mm (0.177 to 0.217 in.) | Opposite edge of seal packing 5.0 mm (0.197 in.) | - | - |
| C - C | 7.0 to 8.0 mm (0.276 to 0.315 in.) | Opposite edge of seal packing 7.5 mm (0.295 in.) | - | - |
| F | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 15.8 mm (0.622 in.) | 50.1 mm (1.97 in.) |
| G | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 10.3 mm (0.406 in.) | 155.1 mm (6.11 in.) |
| H | 7.0 to 8.0 mm (0.276 to 0.315 in.) | - | 19.5 mm (0.768 in.) | 165.4 mm (6.51 in.) |
| I | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 14.6 mm (0.575 in.) | 397.8 mm (1.31 ft.) |
| J | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 18.6 mm (0.732 in.) | 51.4 mm (2.02 in.) |
| K | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 25.3 mm (0.996 in.) | 133.9 mm (5.27 in.) |
| L | 7.0 to 8.0 mm (0.276 to 0.315 in.) | - | 25.8 mm (1.02 in.) | 159.2 mm (6.28 in.) |
| M | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 5.0 mm (0.197 in.) | 185.0 mm (7.28 in.) |
| N | 4.5 to 5.5 mm (0.177 to 0.217 in.) | - | 14.6 mm (0.575 in.) | 397.8 mm (1.31 ft.) |
| O | 4.0 mm (0.157 in.) | Center of seal packing 3.0 mm (0.118 in.) | - | - |
Clean the bolts and their installation holes.
Install the timing chain cover.
![]() |
Temporarily install the engine mounting bracket with the 3 bolts.
![]() |
Install 2 new O-rings.
![]() |
Temporarily install the oil filter bracket with the 4 bolts.
![]() |
Apply adhesive to 5 and a half threads or more of the end of bolt E.
| *1 | Adhesive |
Install the timing chain cover with the 26 bolts and new seal washer in the order shown in the illustration.

| Item | Length | Thread Diameter |
| Bolt A, E | 35 mm (1.38 in.) | 8 mm (0.315 in.) |
| Bolt B | 55 mm (2.17 in.) | 10 mm (0.394 in.) |
| Bolt C | 80 mm (3.15 in.) | 10 mm (0.394 in.) |
| Bolt D | 40 mm (1.57 in.) | 6 mm (0.236 in.) |
| 35. INSTALL TIMING CHAIN COVER OIL SEAL |
![]() |
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.
| 36. INSTALL ENGINE MOUNTING BRACKET STUD BOLT |
![]() |
Install the stud bolt.
| 37. INSTALL CRANKSHAFT PULLEY |
![]() |
Align the key groove of the pulley with the pulley set key.
Temporarily install the pulley with the pulley bolt.
Using SST, hold the pulley in place and tighten the pulley bolt.
| *1 | Hold |
| *2 | Turn |
| 38. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Release the cam, and then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.
![]() |
Install a new gasket, the chain tensioner and bracket with the 2 nuts.
![]() |
Rotate the crankshaft counterclockwise slightly and check that the hook becomes released.
| *1 | Release |
| *2 | Pin |
| *3 | Hook |
| *4 | Turn |
![]() |
Turn the crankshaft clockwise and check that the plunger is extended.
| *1 | Plunger |
| *2 | Plunger Extended |
| *3 | Turn |
| 39. INSTALL OIL FILTER CAP ASSEMBLY |
![]() |
Clean the inside of the oil filter cap, its threads and O-ring groove.
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
| *1 | O-Ring |
Set a new oil filter element in the oil filter cap.
Remove any dirt or foreign matter from the installation surface and inside of the engine.
![]() |
Reapply a small amount of engine oil to the O-ring of the oil filter cap. Align the oil filter cap with the oil filter bracket so that the cutout portion of the cap threads is in a position 90° from the groove in the bracket, and then temporarily install the cap.
![]() |
Using SST, tighten the oil filter cap.
| 40. INSTALL SPARK PLUG TUBE GASKET |
![]() |
Using a cutter knife, cut off the seal part of the removed gasket.
| *1 | Part to Cut Off |
![]() |
Using a hammer and a plug tube gasket which has had the sealing part cut off, uniformly tap in a new plug tube gasket all the way.
| *1 | Plug Tube Gasket without Sealing Part |
| *2 | New Plug Tube Gasket |
| *3 | Claw |
Return the claws of the ventilation baffle plate to their original positions.
| 41. INSTALL CYLINDER HEAD COVER GASKET |
![]() |
Install a new cylinder head cover gasket to the cylinder head cover.
| 42. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Install 3 new gaskets to the camshaft bearing cap.
![]() |
Apply seal packing as shown in the illustration.
![]() |
Install the cylinder head cover with a new seal washer and the 13 bolts.
| 43. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the oil pressure switch.
| *1 | Adhesive |
![]() |
Using a 24 mm deep socket wrench, install the oil pressure switch.
Connect the oil pressure switch connector.
| 44. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Using SST, install a new gasket and the engine coolant temperature sensor.
| 45. INSTALL KNOCK SENSOR |
![]() |
Install the knock sensor with the bolt.
| 46. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-rings of the sensors.
| *1 | New O-Ring |
![]() |
Install the crankshaft position sensor with the bolt.
| 47. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Apply a light coat of engine oil to 2 new O-rings and install them to the camshaft timing oil control valves.
| *1 | New O-Ring |
![]() |
Install the 2 camshaft timing oil control valves and bracket with the 2 bolts.
| *1 | Bracket |
| 48. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-rings of the sensors.
| *1 | O-Ring |
![]() |
Install the 2 camshaft position sensors with the 2 bolts.
| 49. INSTALL SPARK PLUG |
![]() |
Using a 14 mm spark plug wrench and 100 mm extension bar, install the 4 spark plugs.
| 50. INSTALL ENGINE COVER JOINT |
![]() |
Install the 2 engine cover joints.
| 51. INSTALL OIL FILLER CAP GASKET |
![]() |
Install the gasket to the oil filler cap.
| 52. INSTALL OIL FILLER CAP SUB-ASSEMBLY |
![]() |
Install the oil filler cap.