Home › ENGINE ยท 3ZR-FAE › EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


A207703
  1. Install the heat insulator with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD
  1. Install a new exhaust manifold gasket.



    A207702
  1. Install the exhaust manifold with the 5 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



3. INSTALL MANIFOLD STAY


    A207701E01
  1. Temporarily install the manifold stay with the 3 bolts.

  1. While pushing the manifold stay toward the exhaust manifold, tighten the 2 bolts labeled 1.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Tighten the bolt labeled 2.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857E01
  1. Using a vernier caliper, measure the free length of the compression springs.

    Minimum Free Length:
    41.5 mm (1.63 in.)

    If the free length is less than the minimum, replace the compression spring.



    A133205E01
  1. Install a new gasket by hand so that its surface is flush with the exhaust manifold.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the front exhaust pipe.



    A207700
  1. Install the front exhaust pipe and 2 compression springs with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install a new gasket to the front exhaust pipe.



    A207699
  1. Connect the front exhaust pipe to the center exhaust pipe with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A207698
  1. Install the heat insulator with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



6. INSTALL WIRE HARNESS CLAMP BRACKET


    A207697
  1. Install the bracket with the bolt.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. Attach the clamp to connect the fuel hose.



7. INSTALL AIR FUEL RATIO SENSOR


    A213340E01
  1. Using SST, install the sensor to the exhaust manifold.

    SST
    09224-00010  

    Torque:
    without SST :
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

    NOTICE:
    Do not damage the sensor.



    A209087
  1. Connect the sensor connector and clamp.



8. INSTALL NO. 2 CYLINDER HEAD COVER


    A209050
  1. Attach the 4 clips to install the cover.

    NOTICE:
    1. Be sure to attach the clips securely.
    2. Do not apply excessive force or do not hit the cover to attach the clips. This may cause the cover to break.



9. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.