DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 | The calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic). |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio sensor) | +25% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio sensor) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen sensor) | +25% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen sensor) | -12.5% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor Output Voltage | Heated Oxygen Sensor Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P2A00 is output | A |
| DTC P2A00 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B7-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B7-3 (A1A+) - B32-112 (A1A+) | Always | Below 1 Ω |
| B7-4 (A1A-) - B32-113 (A1A-) | Always | Below 1 Ω |
| B7-1 (HA1A) - B32-109 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B7-3 (A1A+) or B32-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B7-4 (A1A-) or B32-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
| B7-1 (HA1A) or B32-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P2A00 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2A00 is output | B |
|
| ||||
| A | ||
| ||