Home › TRANSMISSION ยท CLUTCH › CLUTCH UNIT (for 3ZR-FAE)

CLUTCH UNIT (for 3ZR-FAE) > INSTALLATION

for Preparation Click here


NOTICE:
When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.



1. INSTALL CLUTCH DISC ASSEMBLY


C200452E01
  1. Insert SST into the clutch disc assembly, and then attach them both to the flywheel sub-assembly.

    SST
    09301-00210  

    NOTICE:
    Insert the clutch disc assembly in the correct direction.



2. INSTALL CLUTCH COVER ASSEMBLY


C200449E01
Text in Illustration 
*1
Matchmark
*2
Temporarily Install
  1. Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

    SST
    09301-00210  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Following the order in the illustration, tighten the bolts evenly one at a time.
    2. Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.



3. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY


    C205506E01
  1. Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.5 mm (0.0196 in.)

    If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



4. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY


    C197022
  1. Temporarily install the clutch release cylinder to bleeder tube to a new clutch release with bearing cylinder assembly.

  1. Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.



    C199331
  1. Install the clutch release with bearing cylinder assembly with 3 new bolts.

    Torque:
    23 N*m{ 229 kgf*cm , 17 ft.*lbf }

    NOTICE:
    1. The clutch release with bearing cylinder and installation bolts cannot be reused and must be replaced with new ones.
    2. Clean and degrease all installation surfaces and make sure the clutch release with bearing cylinder fits securely with the transaxle during installation. The first bolt should be tightened by hand while holding the clutch release with bearing cylinder.
    3. Make sure that none of the clutch spline grease adheres to the clutch release with bearing cylinder.
    4. The clutch release with bearing cylinder cannot be disassembled.



    C199330
  1. Install the clutch tube boot to the manual transaxle assembly.



    C199329
  1. Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

  1. Temporarily install the clutch release bleeder sub-assembly with the 2 bolts.



    C202447
  1. Using a union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release with bearing cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



    C199336E01
  1. Apply clutch spline grease to the input shaft spline.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Text in Illustration 
    *1
    Clutch Spline Grease



5. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY


    C199329
  1. Separate the clutch release cylinder to bleeder tube from the clutch release bleeder sub-assembly.

  1. Remove the 2 bolts and clutch release bleeder sub-assembly.



6. INSPECT CLUTCH PIPE LINE


C199335E01
  1. Using SST, apply a pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

    SST
    09992-00242  
    If the pressure drops, replace the clutch release cylinder to bleeder tube.



7. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY


    C199329
  1. Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

  1. Install the clutch release bleeder sub-assembly with the 2 bolts.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }

  1. Using a union nut wrench, install the clutch release cylinder to bleeder tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



8. INSTALL CLUTCH ORIFICE ASSEMBLY


C204176
  1. Install the clutch orifice assembly with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. INSTALL CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE


C204175
  1. Using a union nut wrench, install the clutch release cylinder to accumulator tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



10. INSTALL ORIFICE TO FLEXIBLE HOSE TUBE


C204460
  1. Temporarily tighten the orifice to flexible hose tube onto the clutch orifice assembly.

  1. Install the orifice to flexible hose tube with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Using a union nut wrench, install the orifice to flexible hose tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



11. INSTALL MANUAL TRANSAXLE ASSEMBLY
  1. for EB61:
    Install the manual transaxle assembly (Click here).

  1. for EB61F:
    Install the manual transaxle assembly (Click here).