ENGINE UNIT > INSTALLATION |
| 1. INSTALL NO. 1 VACUUM PUMP BRACKET |
![]() |
Install a new gasket and the vacuum pump bracket with the 2 bolts.
| 2. INSTALL VACUUM PUMP ASSEMBLY |
![]() |
Apply engine oil to 2 new O-rings.
Install the 2 O-rings to the vacuum pump.
![]() |
Apply engine oil to the cylinder hollow.
![]() |
Install the vacuum pump so that the coupling teeth of the vacuum pump (labeled A) and the groove of the camshaft (labeled B) are aligned.
![]() |
Install the vacuum pump with the 3 bolts.
| 3. INSTALL RADIO SETTING CONDENSER |
![]() |
Install the setting condenser with the bolt.
| 4. INSTALL IGNITION COIL ASSEMBLY |
![]() |
Install the 4 ignition coils with the 4 bolts.
| *1 | Cylinder Head Cover |
| *2 | Spark Plug Tube |
| *3 | Plug Cap |
![]() |
Connect the 4 ignition coil connectors.
| 5. INSTALL THERMOSTAT |
Install a new gasket on the thermostat.
![]() |
Install the thermostat to the water inlet housing.
| 6. INSTALL WATER INLET |
Install the water inlet with the 2 nuts.
| 7. INSTALL WATER INLET HOSE |
![]() |
Install the water inlet hose with the 2 clamps.
| 8. INSTALL WATER BY-PASS HOSE |
![]() |
Install the water by-pass hose with the clamp.
| 9. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Install the water by-pass pipe with the 2 bolts.
| 10. CONNECT NO. 3 WATER BY-PASS HOSE |
![]() |
Connect the No. 3 water by-pass hose to the water inlet housing.
| 11. INSTALL VENTILATION HOSE |
Install the ventilation hose to the ventilation valve.
| 12. INSTALL NO. 3 WATER BY-PASS PIPE (for CVT) |
![]() |
Install a new gasket and the water by-pass pipe with the 2 nuts.
| 13. INSTALL EXHAUST MANIFOLD |
Install a new exhaust manifold gasket.
![]() |
Install the exhaust manifold with the 5 nuts.
| 14. INSTALL MANIFOLD STAY |
![]() |
Temporarily install the manifold stay with the 3 bolts.
While pushing the manifold stay toward the exhaust manifold, tighten the 2 bolts labeled 1.
Tighten the bolt labeled 2.
| 15. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 16. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the dipstick guide.
Install the dipstick guide with the bolt.
Install the engine oil level dipstick.
| 17. INSTALL FUEL INJECTOR ASSEMBLY |
![]() |
Install a new injector vibration insulator to the fuel injector.
| *1 | O-Ring |
| *2 | Injector Vibration Insulator |
Apply a light coat of gasoline or spindle oil to the contact surfaces of the O-ring of the fuel injector.
![]() |
While turning the fuel injector left and right, install it to the fuel delivery pipe.
| 18. INSTALL NO. 1 DELIVERY PIPE SPACER |
![]() |
Install the 2 No. 1 delivery pipe spacers to the cylinder head.
| 19. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Install the fuel delivery pipe with the 4 fuel injector assemblies, and then temporarily install the 2 bolts.
![]() |
Tighten the 2 bolts to the specified torque.
![]() |
Install the bolt to secure the fuel delivery pipe.
![]() |
Install the wire harness bracket with the bolt.
| 20. INSTALL FUEL TUBE SUB-ASSEMBLY |
![]() |
Push the fuel tube sub-assembly connector onto the fuel delivery pipe until a "click" sound can be heard.
| *1 | Retainer |
| *2 | Pipe |
| *3 | O-Ring |
![]() |
Install a new No. 2 fuel pipe clamp.
| 21. INSTALL WIRE HARNESS CLAMP BRACKET |
![]() |
Install the wire harness clamp bracket with the 2 nuts.
| 22. INSTALL AIR TUBE |
![]() |
Install the air tube with the 2 bolts.
Connect the No. 2 air hose and No. 1 fuel vapor feed hose.
Connect the 2 union to connector tube hoses.
Connect the fuel vapor feed hose to the purge VSV.
| 23. INSTALL INTAKE MANIFOLD |
![]() |
Using an E6 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.
Install the wire harness clamp bracket to the intake manifold with the bolt.
![]() |
Install a new gasket to the intake manifold.
![]() |
Install the intake manifold and intake manifold stay with the 5 bolts and 2 nuts.
![]() |
Connect the fuel vapor feed hose and ventilation hose.
![]() |
Attach the 4 clamps to the intake manifold.
Install the wire harness clamp bracket with the bolt.
| 24. INSTALL THROTTLE BODY ASSEMBLY |
Install a new gasket into the intake manifold.
![]() |
Install the throttle body with the 2 bolts and 2 nuts.
![]() |
Connect the throttle body connector and 2 water hoses.