Home › ENGINE ยท 3ZR-FAE › CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A233217E01
  1. Using SST and a press, press in a new generator rotor bearing.

    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)



    A153389E03
  1. Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.
    Text in Illustration 
    *1
    Tab
    *2
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY


    A153384
  1. Place the drive end frame on the generator pulley with clutch.

  1. Install the generator rotor to the generator drive end frame.



    A118365
  1. Place the washer on the generator rotor.



3. INSTALL GENERATOR COIL ASSEMBLY


    A153390E04
  1. Using a 21 mm deep socket wrench and a press, slowly press in the generator coil.



    A153382
  1. Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A158992E09
  1. While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.
    Text in Illustration 
    *1
    Pin



    A153391
  1. Install the generator brush holder to the generator coil with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }



    A153392
  1. Pull out the pin from the generator brush holder.



5. INSTALL TERMINAL INSULATOR


    A153393
  1. Install the generator terminal insulator to the generator coil.

    NOTICE:
    Pay attention to installation direction of the generator terminal insulator.



6. INSTALL GENERATOR REAR END COVER


    A153379
  1. Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }



7. INSTALL GENERATOR PULLEY WITH CLUTCH


    A204357E01
  1. Temporarily install the generator pulley with clutch by hand.

  1. Mount generator in a vise between aluminum plates.

  1. Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

    SST
    09820-63021  
    Text in Illustration 
    *1
    Rotor Shaft

    NOTICE:
    Securely attach SST to the generator pulley with clutch and generator rotor shaft.



    A204358E01
  1. Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    Text in Illustration 
    *1
    Hold
    *2
    Turn

    NOTICE:
    1. Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.
    2. Use a torque wrench with a fulcrum length of 400 mm (15.7 in.).
    3. This torque value is effective when SST is parallel to the torque wrench.

  1. Remove the generator from SST.



8. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator pulley with clutch.