Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE
NM30B0U _59 Vehicle Exterior _008635 EXTERIOR PANELS / TRIM _0058990 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  SAFETY FEATURES  


CONSTRUCTION


a.

Impact Absorbing Structure for Frontal Collision

i.

A structure that ensures collision energy absorption efficiency, dissipates impact and minimizes cabin deformation during a frontal collision has been achieved.

·

The front impact energy is transferred to the front side member sub-assembly inner and spread to the rocker through the torque box front.

·

The front impact energy is transferred to the front apron to cowl side member sub-assembly and spread to the front door reinforcement sub-assembly through the MICS* bulkhead.

*: Minimum Intrusion Cabin System


·

The front impact energy is transferred to the front apron to cowl side member sub-assembly and spread to the roof side rails through the reinforcement in the front body pillar such as front body pillar reinforcement UPR.

·

The front impact energy is transferred to the front side member sub-assembly inner and spread to the underbody framework.

V104264
2.906,1.156 2.542,0.667 true 2.771,1.333 2.177,0.948 true 2.292,1.802 1.5,1.615 true 3.448,3.531 3.292,2.906 true 4.167,3.552 3.99,3.156 true 5.313,3.323 5.01,3.021 true 5.979,2.146 5.302,1.813 true 6.063,1.073 5.375,0.875 true 2.396,0.5 2.708,0.656 0.313,0.156 10 false *1 2.021,0.823 2.333,0.979 0.313,0.156 10 false *2 1.333,1.51 1.646,1.667 0.313,0.156 10 false *3 3.385,3.542 3.698,3.698 0.313,0.156 10 false *4 4.135,3.573 4.458,3.729 0.323,0.156 10 false *5 5.333,3.313 5.646,3.469 0.313,0.156 10 false *6 6.031,2.104 6.344,2.26 0.313,0.156 10 false *7 6.115,1 6.427,1.156 0.313,0.156 10 false *8
*1 Front Body Pillar Reinforcement UPR *2 MICS Bulkhead
*3 Front Apron to Cowl Side Member Sub-assembly *4 Front Side Member Sub-assembly Inner
*5 Torque Box Front *6 Rocker
*7 Front Door Reinforcement Sub-assembly *8 Roof Side Rail
V100136

Front Impact Energy
V100135

Dissipate


V104265
1.031,2.271 2.031,1.792 true 3.083,2.594 4.698,0.927 true 0.854,2.208 1.167,2.365 0.313,0.156 10 false *1 4.719,0.771 5.031,0.927 0.313,0.156 10 false *2
*1 Front Side Member Sub-assembly Inner *2 Underbody Framework
V100136

Front Impact Energy
V100135

Dissipate





b.

Impact Absorbing Structure for Side Collision

i.

A structure that ensures collision energy absorption efficiency, dissipates impact and minimizes cabin deformation during a side collision has been achieved.

·

Ultra high-tensile strength sheet steel (980 MPa class) and high-tensile strength sheet steel (590 MPa class) are used for each body frame part, thus ensuring strength against side collisions and achieving weight reduction and structure simplicity.

·

Ultra high-tensile strength sheet steel (980 MPa class) is used for the rocker reinforcement outer and center pillar upper hinge reinforcement No. 1.

·

High-tensile strength sheet steel (590 MPa class) is used for the roof panel reinforcement No. 1 (models with normal roof) and roof side rail outer, etc.

·

Tailored blank steel (material in which 980 Mpa, 590 MPa or 440 MPa class steel sheet was laser-welded in advance) is used for the center body pillar reinforcement outer.


·

Bulkheads (rocker panel reinforcement No. 3, main floor side member reinforcement, front floor reinforcement No. 2 and front floor cross member plate No. 3) are used inside the rocker and in the underbody below the center body pillar, thus achieving a structure which effectively transfers the impact energy during a side collision.

·

The front door side-impact protect beam sub-assembly is optimally positioned and 2 rear door impact protection beams (rear door protect beam sub-assembly No. 2 and rear door protection beam sub-assembly) are provided, thus achieving a structure which effectively transfers the impact load.

V104266
3.385,0.281 3.625,0.719 true 2.677,0.51 3.781,1.542 true 4.573,1.896 6.375,0.573 true 2.729,3.76 3.344,3.01 true 5.104,3.688 4.5,3.156 true 5.938,3.281 5.271,2.927 true 6.135,2.813 5.427,2.573 true 3.76,4.385 3.542,4.531 true 3.99,4.792 3.771,4.938 true 0.448,4.615 0.604,4.771 true 0.313,4.885 0.667,5.042 true 0.333,5.604 0.979,5.25 true 0.844,5.969 1.104,5.469 true 1.854,5.979 1.76,5.583 true 2.229,5.885 1.927,5.615 true 5.365,5.375 5,5.583 true 5.135,4.76 4.833,4.542 true 3.271,0.094 3.583,0.25 0.313,0.156 10 false *1 2.542,0.344 2.854,0.5 0.313,0.156 10 false *2 2.573,3.729 2.885,3.885 0.313,0.156 10 false *3 5.135,3.677 5.448,3.833 0.313,0.156 10 false *4 5.99,3.24 6.302,3.396 0.313,0.156 10 false *5 6.188,2.75 6.5,2.906 0.313,0.156 10 false *6 6.417,0.438 6.729,0.594 0.313,0.156 10 false *7 0.302,4.469 0.615,4.625 0.313,0.156 10 false *8 0.146,4.771 0.458,4.927 0.313,0.156 10 false *9 0.094,5.552 0.417,5.896 0.323,0.344 10 false *10 1.771,6 2.24,6.156 0.469,0.156 10 false *11 2.271,5.854 2.74,6.01 0.469,0.156 10 false *12 3.531,4.885 4,5.042 0.469,0.156 10 false *13 4.604,4.406 5.073,4.563 0.469,0.156 10 false *14 4.417,5.5 5.083,5.76 0.667,0.26 10 false *15 (*16) 1.177,6.292 1.49,6.448 0.313,0.156 10 false *a 3.74,6.292 4.052,6.521 0.313,0.229 10 false *b 5.906,6.292 6.25,6.583 0.344,0.292 10 false *c 3.688,3.49 4,3.646 0.313,0.156 10 false B 3.677,3.094 3.99,3.25 0.313,0.156 10 false B 4.271,3.292 4.583,3.448 0.313,0.156 10 false C 4.26,2.823 4.573,2.979 0.313,0.156 10 false C 4.021,1.99 4.333,2.146 0.313,0.156 10 false A 4.865,1.76 5.177,1.917 0.313,0.156 10 false A 3.792,4.26 4.104,4.417 0.313,0.156 10 false *4 0.75,5.99 1.063,6.146 0.313,0.156 10 false *7
*1 Roof Panel Reinforcement No. 1 *2 Roof Side Rail Outer
*3 Front Door Side-impact Protect Beam Sub-assembly *4 Rocker Reinforcement Outer
*5 Rear Door Protection Beam Sub-assembly *6 Rear Door Protect Beam Sub-assembly No. 2
*7 Center Pillar Upper Hinge Reinforcement No. 1 *8 Center Body Pillar Inner UPR
*9 Belt Anchor to Center Pillar Reinforcement LWR *10 Belt Anchor to Center Pillar Patch
*11 Center Body Pillar Reinforcement Outer *12 Side Panel Outer
*13 Rocker Panel Reinforcement No. 3 *14 Front Floor Cross Member Plate No. 3
*15 Main Floor Side Member Reinforcement *16 Front Floor Reinforcement No. 2
*a A - A Cross Section *b B - B Cross Section
*c C - C Cross Section - -
V100136

Side Impact Energy
V100135

Dissipate


·

A head impact protection structure is used. With this type of construction, if the occupant's head hits against the roof side rail, pillar and back door opening portion in reaction to a collision, the inner panel of the roof side rail and pillar collapses to help reduce the impact.

V104267
0.469,1.854 0.885,1.438 true 3.708,1.823 4.125,1.406 true 5.458,1.844 5.875,1.427 true 0.729,7.26 1.146,6.844 true 3.781,7.375 4.198,6.958 true 0.292,1.813 0.604,1.969 0.313,0.156 10 false *1 3.542,1.781 3.854,1.938 0.313,0.156 10 false *2 5.302,1.813 5.615,1.969 0.313,0.156 10 false *3 0.573,7.219 0.885,7.375 0.313,0.156 10 false *4 3.635,7.354 3.948,7.51 0.313,0.156 10 false *5 0.969,2.125 1.479,2.385 0.51,0.26 10 false *a (*A) 5.885,2.125 6.198,2.281 0.313,0.156 10 false *b 1.344,7.479 1.656,7.635 0.313,0.156 10 false *c 4.938,7.469 5.302,7.698 0.365,0.229 10 false *d 3.417,2.125 3.927,2.385 0.51,0.26 10 false *a (*B) 2.927,2.635 3.146,2.844 0.219,0.208 10 false A 2.844,3.323 3.063,3.531 0.219,0.208 10 false A 5.104,3.052 5.323,3.26 0.219,0.208 10 false B 5.948,3.333 6.167,3.542 0.219,0.208 10 false B 1.167,3.188 1.385,3.396 0.219,0.208 10 false C 1.646,3.719 1.865,3.927 0.219,0.208 10 false C 2.406,3.563 2.625,3.771 0.219,0.208 10 false D 3.021,3.604 3.24,3.813 0.219,0.208 10 false D
*A Models with Normal Roof *B Models with Sliding Roof
*1 Roof Headlining Support *2 Roof Headlining Support No. 3
*3 EA Pad *4 Front Pillar Garnish Assembly
*5 Center Pillar Garnish - -
*a A - A Cross Section *b B - B Cross Section
*c C - C Cross Section *d D - D Cross Section
V100144

Energy Absorber - -


·

A front door trim pad CTR and door trim pad LWR are provided in the door trims to help dampen the impact applied from the side of the vehicle to the occupants.

V104268
1.667,2.583 2.5,1.75 true 4.083,2.583 5.083,1.583 true 2.833,2.135 3.25,2.552 true 5.5,2.146 5.917,2.563 true 1.958,3.677 2.375,4.094 true 1.333,4.479 1.667,4.146 true 4.531,4.563 4.865,4.229 true 5.052,3.635 5.802,4.385 true 1.5,2.552 1.813,2.708 0.313,0.156 10 false *1 3.271,2.552 3.583,2.708 0.313,0.156 10 false *2 3.938,2.563 4.25,2.719 0.313,0.156 10 false *3 5.948,2.552 6.26,2.708 0.313,0.156 10 false *4 1.698,4.594 2.01,4.75 0.313,0.156 10 false *a 4.938,4.594 5.25,4.75 0.313,0.156 10 false *b 2.708,1.167 3.021,1.323 0.313,0.156 10 false A 2.708,2.333 3.021,2.49 0.313,0.156 10 false A 5.344,1.021 5.656,1.177 0.313,0.156 10 false B 5.344,2.344 5.656,2.5 0.313,0.156 10 false B 1.177,4.448 1.49,4.604 0.313,0.156 10 false *2 2.417,4.083 2.729,4.24 0.313,0.156 10 false *1 4.375,4.521 4.688,4.677 0.313,0.156 10 false *4 5.844,4.365 6.156,4.521 0.313,0.156 10 false *3
*1 Front Door Trim Pad CTR *2 Front Door Trim Board Sub-assembly
*3 Door Trim Pad LWR *4 Rear Door Trim Board Sub-assembly
*a A - A Cross Section *b B - B Cross Section





c.

Impact Absorbing Structure for Rear Collision

·

A large-size rear bumper reinforcement (rear bumper reinforcement sub-assembly) is used to spread the impact energy during a rear offset collision. This distributes an impact load to the left and right rear floor side member sub-assembly front, thus suppressing cabin deformation.

V104269
2.49,2.042 1.49,1.292 true 5.615,1.135 4.115,2.188 true 1.323,1.146 1.635,1.302 0.313,0.156 10 false *1 5.646,1 5.958,1.156 0.313,0.156 10 false *2
*1 Rear Bumper Reinforcement Sub-assembly *2 Rear Floor Side Member Sub-assembly Front
V100136

Rear Impact Energy
V100135

Dissipate




d.

Roof Crush Resistance

·

Loads are supported by the front body pillar, center body pillar, roof and header during a roof crush.

·

Front body pillar reinforcement UPR is provided to suppress deformation of the first corner.

·

Belt anchor to center pillar patch is provided to suppress cross sectional deformation of the center body pillar.

·

An integrated construction between the upper and lower parts of the center body pillar inner UPR and large belt anchor to center pillar reinforcement LWR are used. For both of them, high-tensile strength sheet steel (590 MPa class) is used, thus ensuring the rigidity of the center body pillar during a roof crush.

·

Roof panel reinforcement No. 1 which has a large cross section is used on models with a normal roof. In addition, high-tensile strength sheet steel (590 MPa class) is used as the material to suppress the deformation of the center body pillar during a roof crush.

·

High-tensile strength sheet steel (440 MPa class) is used for the windshield header panel inner and front body pillar reinforcement UPR OUT No. 2 to suppress the deformation of the T-shaped part of the front header during a roof crush.

V104270
3.458,0.188 3.75,0.594 true 2.438,0.542 2.896,0.833 true 2.094,2.031 3.719,1.375 true 2.063,3.135 3.115,2.417 true 5.188,3.031 4.469,2.385 true 0.615,4.396 0.281,4.25 true 0.74,4.896 0.292,5.052 true 1.375,5.365 1.031,5.125 true 1.688,4.844 1.323,4.719 true 2.76,5.385 2.313,5.542 true 2.594,5.083 2.281,4.969 true 2.979,4.323 2.51,4.177 true 2.969,4.063 2.677,3.854 true 3.385,5.146 3.073,5.031 true 3.896,4.75 3.667,4.469 true 4.625,4.375 4.333,4.156 true 4.208,3.698 3.906,4.01 true 5.844,4.281 5.615,4 true 5.573,4.365 5.208,4.125 true 5.49,4.656 5.146,4.823 true 6.417,4.583 5.833,5.042 true 6.844,5.073 6.604,4.854 true 3.302,0.042 3.615,0.198 0.313,0.156 10 false *1 2.281,0.385 2.594,0.542 0.313,0.156 10 false *2 1.927,1.979 2.24,2.135 0.313,0.156 10 false *3 1.906,3.094 2.219,3.25 0.313,0.156 10 false *4 5.219,3.031 5.531,3.188 0.313,0.156 10 false *5 0.104,4.146 0.417,4.302 0.313,0.156 10 false *6 0.125,5.01 0.438,5.167 0.313,0.156 10 false *7 1.417,5.344 1.729,5.5 0.313,0.156 10 false *8 2.115,4.875 2.427,5.031 0.313,0.156 10 false *9 3.438,5.094 3.906,5.25 0.469,0.156 10 false *10 3.833,4.771 4.302,4.927 0.469,0.156 10 false *11 4.167,3.531 4.635,3.688 0.469,0.156 10 false *12 4.979,4 5.448,4.156 0.469,0.156 10 false *13 5.615,5.01 6.083,5.167 0.469,0.156 10 false *14 3.406,1.281 3.573,1.563 0.167,0.281 10 false A 3.458,5.531 3.771,5.688 0.313,0.156 10 false *b 5.938,5.521 6.25,5.677 0.313,0.156 10 false *c 3.844,1.615 4.01,1.896 0.167,0.281 10 false A 4.135,1.469 4.302,1.75 0.167,0.281 10 false C 4.833,1.313 5,1.594 0.167,0.281 10 false C 4.552,1.073 4.719,1.354 0.167,0.281 10 false B 4.458,0.74 4.625,1.021 0.167,0.281 10 false B 1.74,4.781 2.052,4.938 0.313,0.156 10 false *3 0.906,5.531 1.219,5.688 0.313,0.156 10 false *a 2.146,5.5 2.458,5.656 0.313,0.156 10 false *5 2.354,4.083 2.667,4.24 0.313,0.156 10 false *7 2.531,3.719 2.844,3.875 0.313,0.156 10 false *6 4.656,4.375 4.969,4.531 0.313,0.156 10 false *1 5.479,3.854 5.792,4.01 0.313,0.156 10 false *5 4.979,4.771 5.292,4.927 0.313,0.156 10 false *9 6.875,5.073 7.083,5.344 0.208,0.271 10 false *6
*1 Roof Panel Reinforcement No. 1 *2 Windshield Header Panel Inner
*3 Front Body Pillar Reinforcement UPR OUT No. 2 *4 Front Body Pillar Reinforcement UPR
*5 Center Body Pillar Inner UPR *6 Side Panel Outer
*7 Roof Side Rail Outer *8 Front Body Pillar UPR Inner
*9 Center Body Pillar Reinforcement Outer *10 Roof Side Rail Inner
*11 Roof Panel Reinforcement Bracket No. 1 *12 Roof Panel
*13 Belt Anchor to Center Pillar Reinforcement LWR *14 Belt Anchor to Center Pillar Patch
*a A - A Cross Section *b B - B Cross Section
*c C - C Cross Section - -





e.

Reduction Pedestrian Head Injury

·

The following shape is used for the cowl panel sub-assembly and cowl top ventilator louver sub-assembly, thus maintaining necessary rigidity and aiming for a reduction of impact against a pedestrian in a collision with a pedestrian.

·

By reducing the rigidity of the cowl top ventilator louver sub-assembly, the counteracting force on pedestrians during a collision has been reduced. As a result, the impact on pedestrians has been reduced.

·

The rear wall of the cowl panel sub-assembly collapses like a pantograph to reduce the counteracting force on pedestrians during a collision. As a result, the impact on pedestrians has been reduced.

·

The dropout zone for the wiper pivot is ensured to allow the pivot to drop easily, thus reducing the counteracting force on pedestrians. As a result, the impact on pedestrians has been reduced.

V104271
1.188,0.396 1.531,0.885 true 0.76,0.646 1.292,1.042 true 2.573,3.51 2.99,3.125 false 2.708,3.719 3.24,3.375 false 1.24,4.396 1.521,4.156 false 2.5,4.823 2.094,4.594 true 2.135,5.292 1.927,5.104 true 1.656,4.823 1.854,4.792 true 1.771,4.958 1.969,4.75 true 4.625,4.375 4.146,4.729 true 4.948,4.5 4.385,5.167 true 5.385,4.99 5.844,5.427 true 5.594,4.896 6.156,5.125 true 5.198,3.854 5.729,3.51 false 5.031,3.438 5.448,3.052 false 0.594,0.51 0.906,0.667 0.313,0.156 10 false *1 1.063,0.208 1.375,0.365 0.313,0.156 10 false *2 3.958,5.115 4.417,5.365 0.458,0.25 10 false *3 (*c) 2.969,2.948 3.427,3.24 0.458,0.292 10 false *4 (*c) 1.719,5.573 2.031,5.729 0.313,0.156 10 false *a 5.167,5.573 5.417,5.792 0.25,0.219 10 false *b 5.479,0.573 5.792,0.729 0.313,0.156 10 false A 4.531,1.844 4.844,2 0.313,0.156 10 false A 5.167,2.146 5.479,2.302 0.313,0.156 10 false B 6.094,0.906 6.406,1.063 0.313,0.156 10 false B 3.271,3.229 3.729,3.521 0.458,0.292 10 false *4 (*d) 1.531,4.01 1.844,4.167 0.313,0.156 10 false *2 2.552,4.771 3.083,5.083 0.531,0.313 10 false *1 (*c) 2.177,5.281 2.708,5.594 0.531,0.313 10 false *1 (*d) 1.49,4.74 1.802,4.896 0.313,0.156 10 false *e 1.635,4.917 1.948,5.073 0.313,0.156 10 false *e 3.99,4.677 4.302,4.833 0.313,0.156 10 false *2 5.875,5.417 6.333,5.667 0.458,0.25 10 false *3 (*d) 6.208,5.073 6.521,5.229 0.313,0.156 10 false *1 5.75,3.354 6.208,3.646 0.458,0.292 10 false *4 (*d) 5.438,2.875 5.896,3.167 0.458,0.292 10 false *4 (*c)
*1 Cowl Panel Sub-assembly *2 Cowl Top Ventilator Louver Sub-assembly
*3 Wiper Pivot *4 Headform Impactor
*a A - A Cross Section *b B - B Cross Section
*c Before Collision *d After Collision
*e Pantograph Structure - -


·

For the front portion of the hood sub-assembly, a structure with sufficient clearance between the hood panel, hood panel reinforcement and hood lock hook is ensured. As a result, a space is made to absorb the collision impact during an accidental contact with pedestrians, thus reducing the impact on pedestrians.

V104272
1.083,1.833 0.719,1.479 true 6.5,0.99 6.031,1.333 false 4.76,1.531 5.104,1.917 false 4.5,1.771 5.063,2.125 true 5.99,2.542 6.438,2.948 false 6.188,1.958 6.563,2.427 true 6.24,1.688 6.677,2.156 true 0.573,1.323 0.885,1.479 0.313,0.156 10 false *1 4.354,1.354 4.823,1.615 0.469,0.26 10 false *2 (*b) 6.458,2.938 6.771,3.094 0.313,0.156 10 false *4 6.521,0.854 6.833,1.01 0.313,0.156 10 false *5 5.688,3.583 6,3.74 0.313,0.156 10 false *a 0.51,2.781 0.823,2.938 0.313,0.156 10 false A 1.26,2.24 1.573,2.396 0.313,0.156 10 false A 4.073,1.646 4.542,1.906 0.469,0.26 10 false *2 (*c) 6.458,2.448 6.927,2.708 0.469,0.26 10 false *3 (*c) 6.552,2.177 7.021,2.438 0.469,0.26 10 false *3 (*b)
*1 Hood Sub-assembly *2 Hood Panel
*3 Hood Panel Reinforcement *4 Hood Lock Hook
*5 Headform Impactor - -
*a A - A Cross Section *b Before Collision
*c After Collision - -


·

Fender brackets (fender apron retainer sub-assembly and front fender apron extension rear) are used in the joint portion of the front fender. The height of the fender bracket and the gap between the fender bracket and the fender have been optimized. Also, fold points are provided on the fender brackets. Therefore, during a collision with a pedestrian, the fender brackets absorb impact energy, with the aim of reducing the potential impact to the pedestrian's head.

V104273
4.458,1.51 4.781,1.823 true 5.854,0.865 6.042,1.177 true 4.406,3.115 4.667,3.833 false 4.052,3.333 4.448,4.052 true 2.885,3.417 3.094,3.677 false 2.448,3.875 3.271,4.458 true 2.198,4.24 3.156,4.708 true 4.833,4.99 5.135,4.604 false 4.313,1.365 4.625,1.521 0.313,0.156 10 false *1 5.74,0.698 6.052,0.854 0.313,0.156 10 false *2 5.146,4.448 5.458,4.604 0.313,0.156 10 false *3 2.75,3.26 3.063,3.417 0.313,0.156 10 false *4 3.729,5.635 4.042,5.792 0.313,0.156 10 false *a 5.073,1.51 5.385,1.667 0.313,0.156 10 false A 4.333,1.885 4.646,2.042 0.313,0.156 10 false A 4.208,2.906 4.667,3.135 0.458,0.229 10 false *2 (*b) 3.823,3.115 4.281,3.344 0.458,0.229 10 false *2 (*c) 1.76,4.135 2.219,4.365 0.458,0.229 10 false *1 (*c) 2.01,3.75 2.469,3.979 0.458,0.229 10 false *1 (*b)
*1 Fender Apron Retainer Sub-assembly *2 Front Fender Apron Extension Rear
*3 Fender Side Apron Sub-assembly *4 Headform Impactor
*a A - A Cross Section *b Before Collision
*c After Collision - -