Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0115 Engine Coolant Temperature Circuit Malfunction An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0117 Engine Coolant Temperature Circuit Low Input A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0118 Engine Coolant Temperature Circuit High Input An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies

HINT:

When any of these DTCs are output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
Higher than 135°C (275°F) Short circuit

MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor circuit and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the engine coolant temperature sensor circuit, and stores DTC P0118. Conversely, if the voltage output is less than 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0117.

MONITOR STRATEGY

Related DTCs P0115: Engine coolant temperature sensor range check (chattering)
P0117: Engine coolant temperature sensor range check (low voltage)
P0118: Engine coolant temperature sensor range check (high voltage)
Required Sensors/Components (Main) Engine coolant temperature sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None

TYPICAL MALFUNCTION THRESHOLDS

P0115
Engine coolant temperature sensor voltage [Engine coolant temperature] Less than 0.14 V, or higher than 4.91 V [Higher than 135°C (275°F), or less than -60°C (-76°F)]

P0117
Engine coolant temperature sensor voltage [Engine coolant temperature] Less than 0.14 V [Higher than 135°C (275°F)]

P0118
Engine coolant temperature sensor voltage [Engine coolant temperature] Higher than 4.91 V [Less than -60°C (-76°F)]

COMPONENT OPERATING RANGE

Engine coolant temperature sensor voltage [Engine coolant temperature] 0.14 to 4.91 V [-60 to 135°C (-76 to 275°F)]

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0115, P0117 or P0118.

11.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A255126
0.219,2.729 0.677,3.042 0.458,0.313 10 B4 0.219,2.896 2.573,3.24 2.354,0.344 10 Engine Coolant Temperature Sensor 1.99,1.49 2.094,1.635 0.104,0.146 10 2 1.99,2.083 2.094,2.229 0.104,0.146 10 1 5.406,1.479 5.854,1.76 0.448,0.281 10 THW 5.156,1.469 5.51,1.781 0.354,0.313 10 95 5.156,2.073 5.406,2.313 0.25,0.24 10 96 5.406,2.083 5.938,2.344 0.531,0.26 10 ETHW 5.99,1.354 6.219,1.688 0.229,0.333 10 R 6.01,1.073 6.354,1.396 0.344,0.323 10 5 V 6,3.094 6.406,3.375 0.406,0.281 10 ECM 5.656,3.104 5.99,3.396 0.333,0.292 10 B77

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).



PROCEDURE

1.READ VALUE USING TECHSTREAM (COOLANT TEMP)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value displayed on the Techstream.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) A
Higher than 135°C (275°F) B
Between 75 and 100°C (167 and 212°F) C


HINT:
·

If there is an open circuit, the Techstream indicates -40°C (-40°F).

·

If there is a short circuit, the Techstream indicates higher than 135°C (275°F).





A

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor connector.

A257884
4.417,1.5 4.75,1.75 0.333,0.25 2.979,1.802 3.313,2.063 0.333,0.26 10 *2 1.146,1.802 1.396,2.01 0.25,0.208 10 *1 2.656,1.031 3.083,1.302 0.427,0.271 10 THW 2.656,1.344 3.125,1.604 0.469,0.26 10 ETHW 4.208,0.271 4.406,0.49 0.198,0.219 10 *a 4.49,1.531 4.833,1.75 0.344,0.219 10 B4
*1 Engine Coolant Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
- -



b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

g.

Read the value displayed on the Techstream.

Standard value:

Higher than 135°C (275°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B4-2 - B77-95 (THW) Always Below 1 Ω
B4-1 - B77-96 (ETHW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255925
0.662,0.158 0.817,0.312 0.155,0.154 10 *1 2.57,0.158 2.725,0.312 0.155,0.154 10 *2 2.226,0.805 2.566,0.958 0.34,0.154 10 THW 2.226,1.183 2.657,1.337 0.431,0.154 10 ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

f.

Read the value displayed on the Techstream.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B4-2 or B77-95 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR