Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A293042
3.323,2.188 3.74,1.771 false 2,0.51 3.073,0.708 1.073,0.198 10 Resistance 1.604,0.229 2.677,0.427 1.073,0.198 10 Fig. 1: 2.115,0.792 3.188,0.99 1.073,0.198 10 [kΩ] 2.208,0.99 2.531,1.188 0.323,0.198 10 30 2.208,1.156 3.281,1.354 1.073,0.198 10 20 2.208,1.438 3.281,1.635 1.073,0.198 10 10 2.281,1.719 3.354,1.917 1.073,0.198 10 5 2.281,1.938 3.354,2.135 1.073,0.198 10 3 2.281,2.104 3.354,2.302 1.073,0.198 10 2 2.271,2.365 3.344,2.563 1.073,0.198 10 1 2.167,2.677 2.667,2.917 0.5,0.24 10 0.5 2.167,2.865 3.24,3.063 1.073,0.198 10 0.3 2.156,3.042 3.229,3.24 1.073,0.198 10 0.2 2.156,3.313 3.229,3.51 1.073,0.198 10 0.1 2.458,3.708 3.531,3.906 1.073,0.198 10 -20 2.833,3.708 3.906,3.906 1.073,0.198 10 0 3.104,3.708 4.177,3.906 1.073,0.198 10 20 3.427,3.708 4.5,3.906 1.073,0.198 10 40 3.729,3.708 4.802,3.906 1.073,0.198 10 60 4.052,3.708 5.125,3.906 1.073,0.198 10 80 4.313,3.708 5.385,3.906 1.073,0.198 10 100 4.802,3.708 5.875,3.906 1.073,0.198 10 [°C] 2.5,3.958 3.573,4.156 1.073,0.198 10 -4 2.802,3.958 3.875,4.156 1.073,0.198 10 32 3.115,3.958 4.188,4.156 1.073,0.198 10 68 3.396,3.958 3.76,4.281 0.365,0.323 10 104 3.698,3.958 4.094,4.292 0.396,0.333 10 140 4.021,3.958 4.417,4.292 0.396,0.333 10 176 4.333,3.958 4.729,4.292 0.396,0.333 10 212 4.781,3.969 5.854,4.167 1.073,0.198 10 [°F] 2.854,4.281 3.927,4.479 1.073,0.198 10 Temperature 3.771,1.625 4.844,1.823 1.073,0.198 10 Acceptable

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0112 Intake Air Temperature Circuit Low Input A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0113 Intake Air Temperature Circuit High Input An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies

HINT:

When any of these DTCs are output, check the intake air temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
Higher than 128°C (262°F) Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.

MONITOR STRATEGY

Related DTCs P0112: Intake air temperature sensor range check (low voltage)
P0113: Intake air temperature sensor range check (high voltage)
Required Sensors/Components (Main) Intake air temperature sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
All of the following conditions are met -
Battery voltage 8 V or higher
Ignition switch ON
Starter Off

TYPICAL MALFUNCTION THRESHOLDS

P0112
Intake air temperature sensor voltage [Intake air temperature] Less than 0.18 V [Higher than 128°C (262°F)]

P0113
Intake air temperature sensor voltage [Intake air temperature] Higher than 4.91 V [Less than -55°C (-67°F)]

COMPONENT OPERATING RANGE

Intake air temperature sensor voltage [Intake air temperature] 0.18 to 4.91 V [-55 to 128°C (-67 to 262°F)]

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0112 or P0113.

11.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A255126
0.219,2.729 0.5,2.917 0.281,0.188 10 B1 0.219,2.896 2.719,3.354 2.5,0.458 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 1.604,1.479 2.073,1.792 0.469,0.313 10 THA 1.708,2.083 2.167,2.354 0.458,0.271 10 E2 1.99,1.49 2.188,1.74 0.198,0.25 10 1 1.99,2.083 2.219,2.292 0.229,0.208 10 2 5.406,1.479 5.75,1.75 0.344,0.271 10 THA 5.167,1.479 5.427,1.688 0.26,0.208 10 93 5.167,2.083 5.417,2.313 0.25,0.229 10 94 5.396,2.073 5.844,2.344 0.448,0.271 10 ETHA 5.99,1.354 6.177,1.563 0.188,0.208 10 R 6.01,1.073 6.354,1.281 0.344,0.208 10 5 V 6,3.104 6.448,3.344 0.448,0.24 10 ECM 5.667,3.104 6,3.333 0.333,0.229 10 B77

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING TECHSTREAM (INTAKE AIR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

e.

Read the value displayed on the Techstream.

OK:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
Higher than 128°C (262°F) B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the Techstream indicates -40°C (-40°F).

·

If there is a short circuit, the Techstream indicates higher than 128°C (262°F).





A

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.

A257883
4.083,1.688 4.417,1.917 0.333,0.229 5.073,1.917 4.854,2.354 false 5.229,1.917 5.479,2.354 false 1.01,1.927 1.156,2.083 0.146,0.156 10 *1 1.365,1.458 1.552,1.615 0.188,0.156 10 E2 1.271,1.156 1.573,1.313 0.302,0.156 10 THA 2.531,1.458 2.927,1.615 0.396,0.156 10 ETHA 2.531,1.156 2.833,1.313 0.302,0.156 10 THA 2.833,1.927 2.979,2.083 0.146,0.156 10 *2 4.073,0.26 4.219,0.417 0.146,0.156 10 *a 4.656,2.365 4.958,2.521 0.302,0.156 10 THA 5.448,2.365 5.635,2.521 0.188,0.156 10 E2 4.167,1.719 4.49,1.917 0.323,0.198 10 B1
*1 Mass Air Flow Meter Sub-assembly *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -



b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

g.

Read the value displayed on the Techstream.

Standard value:

Higher than 128°C (262°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-1 (THA) - B77-93 (THA) Always Below 1 Ω
B1-2 (E2) - B77-94 (ETHA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255925
0.662,0.158 0.817,0.312 0.155,0.154 10 *1 2.57,0.158 2.725,0.312 0.155,0.154 10 *2 2.226,0.805 2.525,0.958 0.299,0.154 10 THA 2.226,1.183 2.616,1.337 0.39,0.154 10 ETHA
*1 Mass Air Flow Meter Sub-assembly
*2 ECM


Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

f.

Read the value displayed on the Techstream.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-1 (THA) or B77-93 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR