Refer to DTC P0136.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136
Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.
When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P0037 | Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) | Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic). | ·
Open in heated oxygen sensor (sensor 2) heater circuit ·
Heated oxygen sensor (sensor 2) ·
EFI-MAIN NO. 2 relay ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P0038 | Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) | Heated oxygen sensor heater current reaches high limit
(Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic). |
·
Short in heated oxygen sensor (sensor 2) heater circuit ·
Heated oxygen sensor (sensor 2) ·
EFI-MAIN NO. 2 relay ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P0141 | Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) | The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic). | ·
Open or short in heated oxygen sensor (sensor 2) heater circuit ·
Heated oxygen sensor (sensor 2) ·
EFI-MAIN NO. 2 relay ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P102D | O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON | Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM | Comes on | DTC stored | DTC for Mexico Models
- Applies |
The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.
If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
After the accumulated heater on time exceeds 100 seconds, the ECM calculates the heater resistance using battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.
| Related DTCs | P0037: Heated oxygen sensor heater (sensor 2) range check (low current)
P0038: Heated oxygen sensor heater (sensor 2) range check (high current) P0141: Heated oxygen sensor heater performance (sensor 2) P102D: Heated oxygen sensor heater performance (sensor 2) |
| Required Sensors/Components (Main) | Heated oxygen sensor heater (sensor 2) |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous: P0037, P0038, P102D
Once per driving cycle: P0141 |
| Duration | 0.5 seconds: P0037
Within 3 seconds: P0038 10 seconds: P0141 0.5 seconds: P102D |
| MIL Operation | Immediate: P0037, P0038, P102D
2 driving cycles: P0141 |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | Off |
| Catalyst active A/F control | Not operating |
| Time after heater on | 10 seconds or more |
| Learned heater off current operation | Completed |
| Learned heater off current operation | Succeeded |
| Oxygen sensor heater high current fail (P0038) | Not detected |
| Heater on current - Learned heater off current | 0.15 A or less |
| Heater output | On |
| All of the following conditions are met | - |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | Off |
| Catalyst active A/F control | Not operating |
| Time after heater on | 10 seconds or more |
| Learned heater off current operation | Completed |
| Oxygen sensor heater high current fail (P0038) | Not detected |
| Heater off current | Higher than 3.5 A |
| Hybrid IC high current limiter monitor input | Fail |
| All of the following conditions are met | - |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | Off |
| Catalyst active A/F control | Not operating |
| Time after heater on | 10 seconds or more |
| Learned heater off current operation | Completed |
| Hybrid IC high current limiter monitor input | Fail |
| Heater output | On |
| All of the following conditions are met | - |
| Heated oxygen sensor heater circuit fail (P0037, P0038 and P102D) | Not detected |
| Battery voltage | 10.5 V or higher |
| Fuel cut | Off |
| Time after fuel cut on to off | 30 seconds or more |
| Accumulated heater on time | 100 seconds or more |
| Learned heater off current operation | Completed |
| Duration that heated oxygen sensor impedance is less than 15 kΩ | 2 seconds or more |
| All of the following conditions are met | - |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | Off |
| Catalyst active A/F control | Not operating |
| Time after heater on | 10 seconds or more |
| Learned heater off current operation | Completed |
| Oxygen sensor heater low current fail (P0037) | Not detected |
| Oxygen sensor heater high current fail (P0038) | Not detected |
| Heater output | Off |
| Heater off current | Higher than 3.5 A |
| Hybrid IC high current limiter monitor input | Fail |
| Heater on current - Learned heater off current | 0.15 A or less |
| Heater on current | 1 A or less |
| Both of the following conditions are met | - |
| Hybrid IC high current limiter monitor input | Fail |
| Heater output | On |
| Heater resistance | Varies with sensor element temperature (Example: Higher than 23 Ω) |
| Heater on current | Higher than 1 A |
Refer to detailed information in Checking Monitor Status.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $42 | $91 | Multiply by 0.001 | Ohm | Oxygen sensor heater resistance bank 1 sensor 2 |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine and idle it for 5 minutes or more [B].
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
Idle the engine for 5 minutes or more [D].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0037, P0038, P0141 or P102D.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Inspect the fuses for circuits related to this system before performing the following procedure.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2].
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click here Engine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
Inspect the heated oxygen sensor.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the heated oxygen sensor.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Heated Oxygen Sensor) |
Disconnect the heated oxygen sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B25-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B25-1 (HT1B) - B77-24 (HT1B) | Always | Below 1 Ω |
| B25-1 (HT1B) or B77-24 (HT1B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0037, P0038, P0141 or P102D is output | B |
A
B
Inspect the EFI-MAIN No. 2 relay.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI-MAIN NO. 2 relay terminal 3 - B25-2 (+B) | Always | Below 1 Ω |
| EFI-MAIN NO. 2 relay terminal 1 - EFI-MAIN NO. 1 relay terminal 3 | Always | Below 1 Ω |
| EFI-MAIN NO. 2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| EFI-MAIN NO. 2 relay terminal 3 or B25-2 (+B) - Body ground | Always | 10 kΩ or higher |
| EFI-MAIN NO. 2 relay terminal 1 or EFI-MAIN NO. 1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG