Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0560 System Voltage An open in the ECM back up power source circuit (1 trip detection logic).
·

Open in back up power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.


MONITOR STRATEGY

Related DTCs P0560: ECM system voltage range check/rationality
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 3 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met -
Battery voltage Below 3.5 V
Stand-by RAM Initialized

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0560.

11.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A300175
1.75,1.146 2.729,1.375 0.979,0.229 10 false FL MAIN 0.854,2.667 1.833,2.896 0.979,0.229 10 false Battery 3.635,1.146 4.729,1.385 1.094,0.24 10 false EFI-MAIN NO.1 5.844,2.073 6.823,2.302 0.979,0.229 10 false E1 5.833,0.875 6.813,1.104 0.979,0.229 10 false BATT 6.135,3.063 6.698,3.292 0.563,0.229 10 false ECM 5.479,0.969 6.042,1.198 0.563,0.229 10 false A62 5.49,2.063 6.052,2.292 0.563,0.229 10 false B77 5.563,0.781 6.125,1.01 0.563,0.229 10 false 1 5.531,1.875 6.094,2.104 0.563,0.229 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Inspect that the battery is not depleted.

Click herePower Source / Network>2AR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A255690
0.417,0.844 0.906,1.135 0.49,0.292 1.458,1.125 0.958,1.615 false 0.135,0.104 0.302,0.281 0.167,0.177 10 *a 0.531,0.917 0.875,1.115 0.344,0.198 10 A62 0.573,1.594 0.969,1.823 0.396,0.229 10 BATT
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0560 is output A
DTC is not output B




A

B