Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0607  Control Module Performance  


MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0607 Control Module Performance Either condition is met (1 trip detection logic):
·

The ECM CPUs malfunction.

·

The heated oxygen sensor transistor (built into the ECM) malfunctions.


·

ECM

·

Heated oxygen sensor (sensor 2)

·

Exhaust gas leak


Comes on DTC stored DTC for Mexico Models
- Not apply

MONITOR STRATEGY

Related DTCs P0607: Control module performance
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous
Duration 60 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
Engine Running
Estimated heated oxygen sensor temperature 450 to 750°C (842 to 1382°F)

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor transistors Fail

CONFIRMATION DRIVING PATTERN

A259532
2.458,2.896 2.094,3.333 false 5.25,2.927 5.938,3.302 0.688,0.375 10 5 minutes or more 6.208,3.406 6.406,3.594 0.198,0.188 10 [I] 1.719,2.281 1.948,2.448 0.229,0.167 10 [B] 2.031,2.281 2.26,2.448 0.229,0.167 10 [C] 2.385,2.031 2.646,2.219 0.26,0.188 10 [D] 2.833,2.031 3.094,2.24 0.26,0.208 10 [E] 3.271,2.031 3.479,2.24 0.208,0.208 10 [F] 0.646,2.146 1.094,2.354 0.448,0.208 10 Idling 1.76,3.354 2.417,3.542 0.656,0.188 10 2 minutes 4.031,0.979 4.25,1.188 0.219,0.208 10 [G] 5.448,0.99 5.667,1.198 0.219,0.208 10 [H] 3.125,2.958 3.688,3.146 0.563,0.188 10 1 minute 0.708,2.958 2.24,3.135 1.531,0.177 10 30 minutes or more 1.365,2.552 1.646,2.792 0.281,0.24 10 [A] 0.479,1.135 1.156,1.323 0.677,0.188 10 80 km/h 0.49,1.531 1.115,1.729 0.625,0.198 10 56 km/h 0.167,2.396 1.177,2.729 1.01,0.333 10 Ignition Switch ON

1.

Stop the engine for 30 minutes or more [A].

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on [B].

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on [C].

7.

Start the engine and wait 2 minutes [D].

8.

Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [E].

9.

Idle the engine for 1 minute [F].

10.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0607, P0136, P0137 or P0138.

16.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [I] again.



17.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0607)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0607 and P0136, P0137 or P0138 are output A
P0607 is output B




A

2.INSPECT DTC (P0136, P0137 OR P0138)

B

3.CHECK FOR EXHAUST GAS LEAK
2.INSPECT DTC (P0136, P0137 OR P0138)
a.

Refer to the P0136, P0137 or P0138 flowchart.

HINT:
·

If P0136 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If P0137 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).




Result:
Proceed to
NEXT



NEXT

6.INSPECT ECM
3.CHECK FOR EXHAUST GAS LEAK
a.

Allow the engine to idle, and then rev the engine.


b.

Check for exhaust gas leaks around the heated oxygen sensor.

If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

HINT:
·

If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.

·

If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

·

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

4.PERFORM CONFIRMATION DRIVING PATTERN
4.PERFORM CONFIRMATION DRIVING PATTERN
A144392
0.03,0.27 3.372,0.433 3.342,0.163 10 Engine Coolant Temperature: 75°C or higher 1.793,0.928 2.047,1.105 0.253,0.177 10 80 1.793,1.313 2.047,1.497 0.253,0.184 10 60 1.659,0.62 2.038,0.804 0.378,0.184 10 km/h 1.922,2.453 2.037,2.61 0.115,0.156 10 0 6.361,2.442 6.722,2.598 0.361,0.156 10 Time 4.546,0.858 5.189,1.015 0.642,0.156 10 5 minutes 4.081,1.189 4.081,0.828 false 5.656,1.189 5.656,0.828 false 4.511,0.914 4.081,0.914 false 5.192,0.914 5.656,0.914 false

a.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

b.

Connect the Techstream to the DLC3.


c.

Start the engine.


d.

Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.


e.

Perform the driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


i.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.


ii.

Drive the vehicle between 60 and 80 km/h (37 and 50 mph) for 5 minutes.



f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0136, P0137, P0138 and/or P0607 are output A
Only P0607 is output B
DTC is not output C




A

5.INSPECT DTC (P0136, P0137 OR P0138)

B

C

6.INSPECT ECM
5.INSPECT DTC (P0136, P0137 OR P0138)
a.

Refer to the P0136, P0137 or P0138 flowchart.

HINT:
·

If P0136 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If P0137 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

·

If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).




Result:
Proceed to
NEXT



NEXT

6.INSPECT ECM
6.INSPECT ECM
a.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

b.

Stop the engine and wait for 30 minutes.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.


e.

Start the engine and allow it to idle for 2 minutes.


f.

Turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0607 is output B




A

END

B