Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction ECM Comes on DTC stored DTC for Mexico Models
- Not apply

DTC No. Monitoring Item Detection Timing Detection Logic
P2610 Soak timer (built into ECM) Engine running 2 trip

DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A290317
4.167,0.833 4.583,1 0.417,0.167 10 IGSW 4.333,2.667 4.583,2.833 0.25,0.167 10 +B 4.167,3.469 4.583,3.635 0.417,0.167 10 MREL 5,1.25 5.75,1.583 0.75,0.333 10 Soak Timer IC 5,2.583 5.667,2.917 0.667,0.333 10 Power Source IC 5,3.417 5.833,3.75 0.833,0.333 10 MAIN Relay Control IC 5.5,4.333 5.917,4.5 0.417,0.167 10 ECM 3.938,1.135 4.271,1.302 0.333,0.167 10 IGN 2.917,1.75 3.25,1.917 0.333,0.167 10 IG2 2.583,3.958 3.667,4.125 1.083,0.167 10 EFI-MAIN NO. 1 1.99,1.135 2.323,1.302 0.333,0.167 10 IG2 0.667,2.104 3.917,2.5 3.25,0.396 10 from Ignition Switch Assembly*1 or Certification ECU (Smart key ECU Assembly)*2 0.583,3.167 1.417,3.333 0.833,0.167 10 from Battery 0.583,4.417 2.333,4.667 1.75,0.25 10 *1: w/o Smart Key System 2.417,4.417 4.083,4.667 1.667,0.25 10 *2: w/ Smart Key System 1.75,3.333 2.833,3.5 1.083,0.167 10 EFI-MAIN NO. 1 0.583,0.979 1.417,1.146 0.833,0.167 10 from Battery

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


MONITOR STRATEGY

Related DTC P2610: ECM internal engine off timer performance
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration -
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None

Case 1
All of the following conditions are met -
Ignition switch ON
Engine Running
Battery voltage 8 V or higher
Starter Off
CPU clock elapsed time 10 minutes or more

Case 2
All of the following conditions are met -
Internal engine off timer (elapsed time from engine stop) 10 minutes or more, and less than 30 minutes
Battery voltage 8 V or higher
Ignition switch ON
Starter Off

Case 3
All of the following conditions are met -
Internal engine off timer (elapsed time from engine stop) 40 minutes or more
Battery voltage 8 V or higher
Ignition switch ON
Starter Off

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Internal engine off timer (elapsed time from engine start) Less than 7 minutes, or more than 13 minutes

Case 2
ECM started by internal engine off timer last trip Yes

Case 3
ECM started by internal engine off timer last trip No

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2610.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


13.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Start the engine and wait for 10 minutes or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


j.

If no pending DTC is output, the repair has been successfully completed.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END