Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140
2.563,4.573 2.844,4.271 2.844,4.271 3.375,4.271 false 3.177,4.813 3.323,5.042 3.323,5.042 3.854,5.042 false 4.771,0.813 6.438,1.021 1.667,0.208 10 Camshaft Position Sensor 4.74,1.323 6.469,1.479 1.729,0.156 10 Crankshaft Position Sensor 0.073,0.01 0.948,0.208 0.875,0.198 10 VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 ECM 1.604,3.75 4.406,3.938 2.802,0.188 10 Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 Duty-cycle 4.5,1.854 6.74,2.073 2.24,0.219 10 Mass Air Flow Meter Sub-assembly 4.458,2.854 6.76,3.052 2.302,0.198 10 Engine Coolant Temperature Sensor 4.844,2.344 6.375,2.51 1.531,0.167 10 Throttle Position Sensor 4.885,3.365 6.323,3.542 1.438,0.177 10 Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 Engine Oil Pressure 3.438,4.219 7.146,4.406 3.708,0.188 10 VVT Controller (Camshaft Timing Exhaust Gear Assembly) 3.885,4.948 5.177,5.135 1.292,0.188 10 Exhaust Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) Open or short in camshaft timing oil control valve assembly (for exhaust camshaft) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust camshaft) circuit

·

Camshaft timing oil control valve assembly (for exhaust camshaft)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for exhaust camshaft) circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0013: Exhaust camshaft timing oil control valve assembly range check
Required Sensors/Components (Main) Exhaust camshaft timing oil control valve assembly
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 1 second
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
All of the following conditions are met -
Starter Off
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met A, B or C
A. All of the following conditions are met -
Battery voltage 11 V or higher, and less than 13 V
Target duty cycle Less than 70%
Output duty cycle 100% or higher
B. All of the following conditions are met -
Battery voltage 13 V or higher
Target duty ratio Less than 80%
Output duty cycle 100% or higher
C. Both of the following conditions are met -
Current cut status Not cut
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

Output duty cycle Higher than 3%, and less than 100%

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0013.

11.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A255118
0.604,1.865 3.406,2.24 2.802,0.375 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) 0.24,1.865 0.531,2.01 0.292,0.146 10 B23 1.594,0.802 1.698,0.948 0.104,0.146 10 1 1.594,1.438 1.698,1.583 0.104,0.146 10 2 4.865,0.802 5.073,0.948 0.208,0.146 10 65 4.865,1.438 5.063,1.583 0.198,0.146 10 64 5.135,1.448 5.542,1.594 0.406,0.146 10 OE1- 5.135,0.813 5.542,0.958 0.406,0.146 10 OE1+ 5.656,2.229 5.99,2.375 0.333,0.146 10 ECM 5.323,2.229 5.615,2.375 0.292,0.146 10 B77

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is output, check the VVT system (for exhaust camshaft) circuit.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (DTC P0013)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0013 is output A
DTC is not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B23-1 - B77-65 (OE1+) Always Below 1 Ω
B23-2 - B77-64 (OE1-) Always Below 1 Ω
B23-1 or B77-65 (OE1+) - Body ground Always 10 kΩ or higher
B23-2 or B77-64 (OE1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR