Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P060A  Internal Control Module Monitoring Processor Performance  


MONITOR DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, the DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060A Internal Control Module Monitoring Processor Performance A CPU reset is performed after one of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.

·

There is an electronic throttle monitoring CPU error.


ECM Comes on DTC stored DTC for Mexico Models
- Applies

MONITOR STRATEGY

Related DTCs P060A: Internal control module monitoring processor performance
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration -
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None

TYPICAL MALFUNCTION THRESHOLDS

Either of the following conditions is met 1 or 2
1. All of the following conditions are met -
CPU reset 1 time or more
Learned throttle position - Learned accelerator pedal position 0.4 V or higher
Electronic throttle actuator Off
2. CPU reset 2 times or more

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the Techstream off.

5.

Turn the ignition switch off.

6.

Disconnect the Techstream.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the Techstream to the DLC3.

10.

Turn the ignition switch to ON and turn the Techstream on.

11.

Wait 16 seconds or more.

12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P060A.

16.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P060A)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and turn the Techstream off.


f.

Disconnect the Techstream.


g.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


h.

Connect the cable to the battery negative (-) battery terminal.


i.

Connect the Techstream to the DLC3.


j.

Turn the ignition switch to ON.


k.

Turn the Techstream on.


l.

Wait 16 seconds or more.


m.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


n.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P060A is output B




A

B