Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P011B  Engine Coolant Temperature / Intake Air Temperature Correlation  


DESCRIPTION

The engine has two temperature sensors, an engine coolant temperature sensor and an intake air temperature sensor, to detect temperature while the engine is operating. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection duration and the ignition timing to control the engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P011B Engine Coolant Temperature / Intake Air Temperature Correlation

All of the following conditions are met (2 trip detection logic):

1.

The battery voltage is 10.5 V or higher.

2.

7 hours or more have elapsed since the engine stopped on the previous trip.

3.

60 seconds or more after a cold engine start.

4.

Either of the following conditions is met:

1.

The minimum intake air temperature after the engine starts is -10°C (14°F) or higher.

2.

Engine coolant temperature before the engine starts is -10°C (14°F) or higher.


5.

The difference between the readings of the engine coolant temperature and intake air temperature is higher than 25°C (45°F).



·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored DTC for Mexico Models
- Not apply

A204087
0.25,0.24 3.375,0.865 3.125,0.625 10 Difference Between Engine Coolant Temperature and Intake Air Temperature 0.552,1.521 0.948,1.688 0.396,0.167 10 40 0.458,3.115 0.719,3.281 0.26,0.167 10 0 0.552,2.365 0.917,2.531 0.365,0.167 10 25 0.51,3.802 0.969,3.969 0.458,0.167 10 -25 3.656,1.583 4.448,1.802 0.792,0.219 10 60 Seconds 4.375,1.823 4.656,2.042 0.281,0.219 10 Fail 4.99,2.385 5.385,2.583 0.396,0.198 10 25°C 4.198,4.333 4.552,4.573 0.354,0.24 10 Fail 4.99,3.802 5.448,4 0.458,0.198 10 -25°C 1.99,4.896 2.167,5.063 0.177,0.167 10 5 2.438,4.885 2.615,5.052 0.177,0.167 10 7 0.469,5.177 1.74,5.396 1.271,0.219 10 Ignition Switch off 2.927,5.167 3.781,5.385 0.854,0.219 10 Engine Start 5.979,4.917 6.594,5.135 0.615,0.219 10 Time (h) 0.76,1.115 1.031,1.313 0.271,0.198 10 °C

HINT:
·

Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it is not possible to accurately compare the readings.


·

For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the engine coolant temperature and intake air temperature are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, but this does not necessarily indicate a fault.



MONITOR DESCRIPTION

The ECM monitors the difference between the engine coolant temperature and the intake air temperature when the engine is started cold to accurately detect the engine temperature conditions. The monitor runs when the engine is started after 7 hours or more have elapsed since the engine was stopped (ignition switch turned off) on the previous trip. If the difference between the engine coolant temperature and the intake air temperature on a cold start exceeds 25°C (45°F), the ECM interprets this as a malfunction in the engine coolant temperature sensor circuit and intake air temperature sensor circuit, and stores the DTC.

MONITOR STRATEGY

Related DTCs P011B: Engine coolant temperature/intake air temperature sensor correlation
Required Sensors/Components (Main) Engine coolant temperature sensor
Intake air temperature sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration -
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
All of the following conditions are met -
Time after ignition switch ON and engine not running Less than 20 seconds
Soak Time 7 hours or more
Battery voltage 10.5 V or higher
Time after engine start 60 seconds or more
Either of the following conditions is met (a) or (b)
(a) Minimum intake air temperature after engine start -10°C (14°F) or higher
(b) Engine coolant temperature before engine start -10°C (14°F) or higher
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) Not detected
Intake air temperature sensor circuit fail (P0112, P0113) Not detected
Mass air flow meter circuit fail (P0102, P0103) Not detected
Soak timer circuit fail (P2610) Not detected

TYPICAL MALFUNCTION THRESHOLDS

Deviated engine coolant temperature and intake air temperature Less than -25°C (-45°F), or higher than 25°C (45°F)

CONFIRMATION DRIVING PATTERN

A213993
0.987,1.211 1.403,1.414 0.416,0.203 10 Idling 0.239,2.257 1.395,2.413 1.156,0.156 10 Ignition Switch off 2.079,1.623 2.298,1.842 0.219,0.219 10 [A] 3.385,2.11 3.583,2.306 0.198,0.196 10 [B] 5.224,1.077 5.439,1.278 0.215,0.201 10 [C] 6.166,2.867 6.387,3.056 0.22,0.189 10 [D] 4.723,2.579 6.005,2.756 1.281,0.177 10 60 seconds or more 2.947,2.516 4.069,2.679 1.122,0.163 10 7.5 hours or more 0.239,1.767 1.478,1.923 1.239,0.156 10 Ignition Switch ON

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) [A].

4.

Turn the ignition switch off.

5.

With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Start the engine and wait 60 seconds or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P011B.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P011B is output A
DTC P011B and other DTCs are output B


HINT:

If any DTCs other than P011B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (INTAKE AIR)

B

2.READ VALUE USING TECHSTREAM (INTAKE AIR)
a.

Leave the vehicle for 7 hours or more.

HINT:

It is necessary to leave the vehicle for 7 hours or more to create conditions similar to the DTC detection conditions.



b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

f.

Read the value displayed on the Techstream.

Standard:

Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

Temperature readings on the outside temperature gauge of the vehicle (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built in to prevent swings in the temperature display. Use an accurate thermometer to determine the outside air temperature.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value displayed on the Techstream.

Standard:

The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

If the result is not as specified, check that there are no heat sources such as a block heater in the engine compartment.

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG