The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves and valve body.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0796 | Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) | Either condition is met (2-trip detection logic):
·
The engine revs freely when a shift to 2nd or 6th gear is commanded. ·
The following condition is met twice: When a shift to 1st gear is commanded, 2nd gear is engaged. |
·
Shift solenoid valve SL3 remains open or closed ·
Transmission valve body assembly is blocked ·
Automatic transaxle assembly (clutch, brake or gear etc.) |
Comes on | DTC stored |
The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft speed, intermediate (counter) shaft speed and output shaft speed, the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores the DTC.
| Related DTCs | P0796:
Shift solenoid valve SL3/OFF malfunction/Functional check Shift solenoid valve SL3/ON malfunction/Functional check |
| Required sensors/Components | Shift solenoid valve SL3, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and (B): 0.5 sec.
OFF malfunction (C) and (D): 0.8 sec. ON malfunction: 0.8 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | P0712, P0713 (ATF temperature sensor circuit)
P0115, P0117, P0118 (ECT sensor circuit) P0715, P0717 (Turbine speed sensor circuit) P0791, P0793 (Intermediate shaft speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P2810 (Shift solenoid valve SL4 circuit) P0327, P0328 (KCS circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (ETCS) U0100 (CAN communication system) |
| ATF temperature sensor circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| Turbine speed sensor circuit | Not circuit malfunction |
| Intermediate shaft speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| Shift solenoid valve SL3 circuit | Not circuit malfunction |
| Shift solenoid valve SL4 circuit | Not circuit malfunction |
| KCS (Knock control sensor) circuit | Not circuit malfunction |
| ETCS (Electronic throttle control system) | Not system down |
| CAN communication system | Not system down |
| Transmission range | "D" |
| Duration time from shifting "N" to "D" | 4 sec. or more |
| ATF temperature | -10°C (14°F) or higher |
| Engine | Starting |
| ECM selected gear | 2nd |
| Throttle valve opening angle | 3% or more |
| ECM indicated pressure value of SL1 | 1200 kPa (12.2 kgf/cm2, 174 psi) |
| ECM indicated pressure value of SL2 | 0 kPa (0 kgf/cm2, 0 psi) |
| ECM indicated pressure value of SL3 | 1200 kPa (12.2 kgf/cm2, 174 psi) |
| ECM selected gear | 6th |
| Throttle valve opening angle | 3% or more |
| ECM indicated pressure value of SL1 | 0 kPa (0 kgf/cm2, 0 psi) |
| ECM indicated pressure value of SL2 | 1200 kPa (12.2 kgf/cm2, 174 psi) |
| ECM indicated pressure value of SL3 | 1200 kPa (12.2 kgf/cm2, 174 psi) |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle:
(When condition "D" is not detected) |
6.5% or more at engine speed of 2000 rpm (Condition varies with engine speed) |
| Throttle valve opening angle:
(When condition "D" is detected) |
3.0% or more at output speed of 750 rpm (Condition varies with output speed) |
| ECT | 40°C (104°F) or higher |
| Throttle valve opening angle:
(After transition to 2nd gear) |
3.0% or more at output speed of 750 rpm (Condition varies with output speed) |
| ECM selected gear | 1st |
| Vehicle speed | 2 to 40 km/h (1.2 to 24.9 mph) |
| Engine speed - Turbine speed | 50 rpm or more |
| ECT | 40°C (104°F) or higher |
One of the following conditions is met: OFF malfunction (A), (B) or ((C) and (D))
| Turbine speed - Output speed x 2nd gear ratio | 1000 rpm or more |
| Turbine speed - Output speed x 6th gear ratio | 1000 rpm or more |
| Turbine speed / Output speed when output speed less than 1000 rpm | 3.232 to 7.556 |
2 detections are necessary per driving cycle:
1st detection: temporary flag ON
2nd detection: pending fault code ON
| Turbine speed / Output speed when output speed less than 1000 rpm | 1.860 to 2.289 |
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Perform the universal trip to clear permanent DTCs.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
|---|---|
| Only P0796 is output | A |
| P0796 and other DTCs are output | B |
If shift solenoid valve SL3 is stuck off, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.
A
B
This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
The gear commanded by the ECM is shown in the Data List / Shift Status display on the Techstream.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate the shift solenoid valves and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Can be used to check the operation of the shift solenoid valves.
A 10-second interval is required between gear changes. Do not down-shift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (30 mph) or less |
| Active Test Display |
|---|
| Control the Shift Position |
| Data List Display |
|---|
| Shift Status |
This test can be conducted when the vehicle is stopped.
When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
|---|---|---|---|---|---|
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the ECM commanded gear and the actual gear.
| System Condition | ECM Gear Shift Command | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Malfunction | Shift solenoid valve SL1 Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Shift solenoid valve SL1 Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid valve SL2 Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B | |
| Shift solenoid valve SL2 Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid valve SL3 Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C | |
| Shift solenoid valve SL3 Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid valve SL4 Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D | |
| Shift solenoid valve SL4 Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid valve SLT Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E | |
| Shift solenoid valve SLT Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
*1: Neutral
*2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is less than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
*3: When shift solenoid valve SLT is stuck off, gear shifting is normal.
A
B
C
D
E
| *1 | Shift Solenoid Valve SL3 |
Remove shift solenoid valve SL3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG