Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0748 | Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) | An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gears (SL1 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic). | ·
Open or short in shift solenoid valve SL1 circuit ·
Shift solenoid valve SL1 ·
Wiring harness connector ·
ECM |
Comes on | DTC stored |
This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)
While driving and shifting between 4th and 5th gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines there is a malfunction.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
| Related DTCs | P0748: Shift solenoid valve SL1/Range check |
| Required sensors/Components | Shift solenoid valve SL1 |
| Frequency of operation | Continuous |
| Duration | 1 sec. |
| MIL operation | Immediate |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | None |
| Ignition switch | ON |
| Starter | OFF |
| Battery voltage | 12 V or higher |
| Battery voltage | 10 V or higher and below 12 V |
| Target current | Below 0.75 A |
| Battery voltage | 8 V or higher |
| Target current | 0.25 A or higher |
One of the following conditions is met: Condition (A), (B) or (C)
| Output duty cycle | 100% or more |
| Output duty cycle | 0% or less |
| Output duty cycle | More than 0% and less than 100% |
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Perform the universal trip to clear permanent DTCs.
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
The following table shows normal operation of shift solenoid valve SL1 when the shift lever is in D:
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve SL1 | ON | ON | ON | ON | OFF | OFF |
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B77-5 (SL1+) - B77-4 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| B77-5 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| B77-4 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B78 wiring harness connector.
Disconnect the B77 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B78-17 (SL1+) - B77-5 (SL1+) | Always | Below 1 Ω |
| B78-16 (SL1-) - B77-4 (SL1-) | Always | Below 1 Ω |
| B78-17 (SL1+) or B77-5 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| B78-16 (SL1-) or B77-4 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Transmission Wire) |
Remove the wiring harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-14 (SL1+) - A-13 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| A-14 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| A-13 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Solenoid Valve SL1 |
Remove shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG