Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0049436 AUTOMATIC TRANSAXLE SYSTEM D

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

When troubleshooting On-Board Diagnostic (OBD II) vehicles, the vehicle must be connected to the OBD II scan tool (complying with SAE J1987). Various data output from the vehicle ECM can then be read.


b.
C140856

OBD II regulations require that the vehicle on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components


ii.

The powertrain control components (which affect vehicle emissions)


iii.

The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by SAE J2012 are recorded in the ECM memory.

When a malfunction does not reoccur, the MIL stays illuminated until the ignition switch is turned off, and the MIL turns off when the engine is started. However, the DTCs will remain recorded in the ECM memory.



c.

To check DTCs, connect the Techstream to the Data Link Connector 3 (DLC3) of the vehicle. The Techstream displays DTCs, freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared with the Techstream.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR



NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions.



2 TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837
0.354,1.74 2.792,1.99 2.438,0.25 10 false Freeze frame data which can be read 0.698,0.708 1.323,0.906 0.625,0.198 10 false 0.5 sec. 1.333,0.708 1.958,0.906 0.625,0.198 10 false 0.5 sec. 1.99,0.708 2.615,0.906 0.625,0.198 10 false 0.5 sec. 1.823,0.104 2.875,0.396 1.052,0.292 10 false DTC is stored

The Techstream records freeze frame data in 5 different instances: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. These sets of data can be used to simulate the vehicle condition around the time when the malfunction occurred. The data may help in finding the cause of the malfunction, or in judging if the DTC was caused by a temporary malfunction.



CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK MIL


a.

Check that the MIL illuminates when turning the ignition switch to ON.

If the MIL does not illuminate, there is a problem in the MIL circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit


b.

When the engine is started, the MIL should turn off.