Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0049436 AUTOMATIC TRANSAXLE SYSTEM D

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


a.

Measure the line pressure.

CAUTION:

The line pressure test should always be carried out with at least 2 people. One person should observe the condition of wheels and wheel chocks while the other is performing the test.


NOTICE:
·

Perform a test at the normal operating Automatic Transaxle Fluid (ATF) temperature: 50 to 80°C (122 to 176°F)

·

Be careful to prevent the hose of SST from interfering with the exhaust pipe.

·

This check must be conducted after checking and confirming that the engine is normal.

·

Perform the test with the A/C off.

·

Do not perform the stall test for longer than 5 seconds.



i.

Warm up the ATF.


ii.

Lift the vehicle up.


iii.

Remove the engine under cover.


iv.
C226143
2.417,0.604 2.531,0.417 false 0.604,1.844 0.719,1.656 false 2.563,0.323 3.021,0.521 0.458,0.198 10 SST 0.313,1.771 0.771,1.969 0.458,0.198 10 SST

Remove the test plug on the transaxle case and install SST.

SST
09992-00095  (09992-00231, 09992-00271)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock the 4 wheels.


vii.

Connect the Techstream to the DLC3.


viii.

Start the engine.


ix.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Shift Position.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Shift Position
50004 234 116

x.

Move the shift lever to D, and then use the Techstream to hold 3rd gear using Active Test. Measure the line pressure while the engine is idling.

Specified Line Pressure
Condition Shift Lever in D
Idling 360 to 430 kPa
(3.7 to 4.4 kgf/cm2, 52 to 62 psi)


xi.

Turn the ignition switch off.


xii.
C267931

Disconnect the harness connector from the wiring harness connector.

HINT:

Disconnect the connector only when performing the D position stall test.



xiii.

Start the engine.


xiv.

Firmly depress the brake pedal, move the shift lever to D, depress the accelerator pedal all the way down, and check the line pressure while the stall test is performed.

Specified Line Pressure
Condition Shift Lever in D
Stall test 1160 to 1350 kPa
(11.8 to 13.8 kgf/cm2, 168 to 196 psi)


xv.

Turn the ignition switch off.


xvi.

Connect the harness connector, depress the brake pedal firmly, move the shift lever to R, and check that the line pressure while the engine is idling and during the stall test.

Specified Line Pressure
Condition Shift Lever in R
Idling 670 to 820 kPa
(6.8 to 8.4 kgf/cm2, 97 to 119 psi)
Stall test 1650 to 1910 kPa
(16.8 to 19.5 kgf/cm2, 239 to 277 psi)


xvii.

Remove SST, install the test plug.


xviii.

Clear the DTCs.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Evaluation
Test Result Possible Cause
Measured values are higher than the specified value in all positions
·

Shift solenoid valve SLT defective

·

Regulator valve defective


Measured values are lower than the specified value in all positions
·

Shift solenoid valve SLT defective

·

Regulator valve defective

·

Oil pump defective


Pressure is low in D only
·

D position circuit fluid leak

·

Clutch No. 1 (C1) defective


Pressure is low in R only
·

R position circuit fluid leak

·

Brake No. 2 (B2) defective

·

Brake No. 3 (B3) defective