Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0049436 AUTOMATIC TRANSAXLE SYSTEM C

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2810  Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2810 Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL4 circuit while driving and shifting gears (SL4 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).
·

Open or short in shift solenoid valve SL4 circuit

·

Shift solenoid valve SL4

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

MONITOR STRATEGY

Related DTCs P2810: Shift solenoid valve SL4/Range check
Required sensors/Components Shift solenoid valve SL4
Frequency of operation Continuous
Duration 1 sec.
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not stored None
Ignition switch ON
Starter OFF

Condition (A)
Battery voltage 12 V or higher

Condition (B)
Battery voltage 10 V or higher and below 12 V
Target current Below 0.75 A

Condition (C)
Battery voltage 12 V or higher
Target current 0.6 A or higher

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition (A), (B) or (C)

Condition (A) and (B)
Output duty cycle 100% or more

Condition (C)
Output duty cycle 0% or less

COMPONENT OPERATING RANGE

Output duty cycle More than 0% and less than 100%

WIRING DIAGRAM

C239277
5.677,4.365 6.104,4.552 0.427,0.188 10 false ECM 5.083,1.229 5.51,1.417 0.427,0.188 10 false SL4+ 5.083,2.635 5.51,2.823 0.427,0.188 10 false SL4- 3.615,1.229 4.042,1.417 0.427,0.188 10 false SL4+ 3.615,2.635 4.042,2.823 0.427,0.188 10 false SL4- 1.625,1.927 2.563,2.26 0.938,0.333 10 false Shift Solenoid Valve SL4 1.146,3.417 2.5,3.604 1.354,0.188 10 false Transmission Wire 3.063,3.427 4.063,3.781 1,0.354 10 false Wiring Harness Connector 5.677,4.188 5.969,4.344 0.292,0.156 10 false B77 4.885,1.479 5.01,1.656 0.125,0.177 10 false 9 4.885,2.865 5.01,3.042 0.125,0.177 10 false 8 3.104,1.229 3.531,1.417 0.427,0.188 10 false SL4+ 3.104,2.635 3.531,2.823 0.427,0.188 10 false SL4- 2.344,1.229 2.771,1.417 0.427,0.188 10 false SL4+ 2.344,2.635 2.771,2.823 0.427,0.188 10 false SL4- 4.083,1.167 4.271,1.323 0.188,0.156 10 false 21 4.083,2.563 4.271,2.719 0.188,0.156 10 false 20 2.802,1.177 2.99,1.333 0.188,0.156 10 false 22 2.802,2.563 2.99,2.719 0.188,0.156 10 false 21 2.833,2.76 3.125,2.917 0.292,0.156 10 false A 2.823,1.375 3.115,1.531 0.292,0.156 10 false A 4.031,2.76 4.438,2.927 0.406,0.167 10 false B78 4.031,1.365 4.51,1.521 0.479,0.156 10 false B78 1.417,1.708 1.844,1.896 0.427,0.188 10 false 1 1.417,2.365 1.844,2.552 0.427,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·


HINT:

The following table shows the normal operation of shift solenoid valve SL4 when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL4 OFF OFF ON OFF ON OFF


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL4 CIRCUIT)
a.
C267934
1.448,0.177 1.865,0.385 0.417,0.208 0.552,1.719 0.854,0.885 true 1.375,1.708 0.917,0.885 true 1.531,0.208 1.99,0.406 0.458,0.198 10 false B77 0.313,1.75 1.021,1.969 0.708,0.219 10 false 8 (SL4-) 1.156,1.75 1.875,1.969 0.719,0.219 10 false 9 (SL4+) 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-9 (SL4+) - B77-8 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
B77-9 (SL4+) - Body ground and other terminals Always 10 kΩ or higher
B77-8 (SL4-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
a.

Disconnect the B78 wiring harness connector.


b.

Disconnect the B77 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-21 (SL4+) - B77-9 (SL4+) Always Below 1 Ω
B78-20 (SL4-) - B77-8 (SL4-) Always Below 1 Ω
B78-21 (SL4+) or B77-9 (SL4+) - Body ground and other terminals Always 10 kΩ or higher
B78-20 (SL4-) or B77-8 (SL4-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)
a.
C226545
0.594,0.76 0.938,1 0.344,0.24 1.219,1.51 1.427,1.135 true 1.708,1.51 1.542,1.135 true 0.354,0.219 0.667,0.417 0.313,0.198 10 *a 1.052,1.552 1.667,1.75 0.615,0.198 10 SL4+ 1.594,1.552 2.208,1.75 0.615,0.198 10 SL4- 0.708,0.792 1.063,0.99 0.354,0.198 10 A
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-22 (SL4+) - A-21 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
A-22 (SL4+) - Body ground and other terminals Always 10 kΩ or higher
A-21 (SL4-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SL4
4.INSPECT SHIFT SOLENOID VALVE SL4
a.
C197715
1.781,0.969 2.167,0.427 true 1.781,2.948 2.167,2.406 true 1.469,0.969 1.083,0.417 true 1.469,2.948 1.083,2.396 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.198,0.323 2.375,0.542 0.177,0.219 10 1 2.198,2.302 2.375,2.521 0.177,0.219 10 1 0.969,0.323 1.146,0.542 0.177,0.219 10 2 0.969,2.313 1.146,2.531 0.177,0.219 10 2 1.854,3.938 2.313,4.135 0.458,0.198 10 (+) 1.271,3.938 1.729,4.135 0.458,0.198 10 (-)
*1 Shift Solenoid Valve SL4


Remove shift solenoid valve SL4.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG