Home › Engine / Hybrid System › 2AR-FE EMISSION CONTROL › CANISTER
RM30B0U _51 Engine / Hybrid System _009089 2AR-FE EMISSION CONTROL _0049670 CANISTER A

2AR-FE EMISSION CONTROL  CANISTER  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT FLOOR COVER

Hide 2.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A293408
2.042,1.813 2.198,2.01 0.156,0.198 10 A

Remove the nut, 3 clips and No. 1 fuel tank protector.

HINT:

The clip labeled A cannot be removed from the No. 1 fuel tank protector.



Hide 3.REMOVE CHARCOAL CANISTER ASSEMBLY

a.
A293407
0.802,1.146 1.417,1.146 true 2.302,1.229 2.594,1.51 true 1.542,1.552 1.542,1.375 1.542,1.375 1.813,1.042 true 1.375,2.75 1.375,2.604 1.375,2.604 1.135,2.51 false 2.438,2.073 2.667,2.073 2.667,2.073 2.76,2.323 true 0.625,1.073 0.792,1.25 0.167,0.177 10 true *1 2.552,1.531 2.74,1.698 0.188,0.167 10 true *2 1.469,1.594 1.667,1.781 0.198,0.188 10 true *3 0.542,2.083 0.854,2.24 0.313,0.156 10 false *a 2.146,2.688 2.458,2.844 0.313,0.156 10 false *b 2.281,2 2.594,2.198 0.313,0.198 10 false *4 1.281,2.76 1.594,2.958 0.313,0.198 10 false *4
*1 Vent Line Hose
*2 Air Inlet Line Hose
*3 Purge Line Hose
*4 Retainer
*a Pull Out
*b Push


Disconnect the connector.


b.

Slide the clamp and disconnect the purge line hose.


c.

Disconnect the air inlet line hose.

i.

Push in the retainer and pull out the air inlet line hose straight from the pipe.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the canister and around the hose. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the charcoal canister assembly and hose.

·

When disconnecting the hose, make sure that the retainer is not lifted.





d.

Disconnect the vent line hose.

i.

Pinch the retainer and then raise it.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the charcoal canister assembly and around the hose. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the charcoal canister assembly and hose.





e.
A293779

Remove the 4 bolts, clip and charcoal canister assembly.


Hide 4.REMOVE CHARCOAL CANISTER BASE BRACKET

a.
A293410

Detach the claw and remove the charcoal canister base bracket.


Hide 5.REMOVE CHARCOAL CANISTER PROTECTOR

a.
A293409

Detach the claw and remove the charcoal canister protector.


Hide 6.REMOVE CANISTER PUMP MODULE

a.

Before removing the canister pump module, clean the canister by blowing air into it to ensure that the canister is free of foreign matter.

NOTICE:
·

Make sure to clean the canister using only air.


·

Do not use gasoline, thinners or solvents.




b.
A263349
1.354,1.521 2.385,1.865 2.385,1.865 2.635,1.865 true 2.677,1.792 2.99,1.948 0.313,0.156 10 *1
*1 Protective Tape


While disengaging the 2 claws as shown in the illustration, push the canister pump module upwards using a screwdriver to remove it.

HINT:

Tape the screwdriver tip before use.



c.
A263350

Check if the canister contains foreign matter such as mud or water.

i.

Visually check that the inside of the canister is free of foreign matter.


ii.

Hold the canister upside down to make sure that the canister is free of foreign matter.

If the charcoal canister assembly contains foreign matter, replace the charcoal canister assembly.