Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL SYSTEM
RM30B0U _51 Engine / Hybrid System _009210 2AR-FE FUEL _0050315 FUEL SYSTEM G

2AR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the Techstream on.


d.

for 2WD

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

e.

for 4WD

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

f.

Check the fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the C/OPN relay, fuel pump, ECM, fuel pump control ECU and wiring connector.



g.

Check for fuel leaks.

i.

Check that there are no fuel leaks after performing maintenance anywhere on the system.

If there are fuel leaks, repair or replace parts as necessary.



Hide 2.CHECK FUEL PRESSURE

a.

Using a voltmeter, measure the battery voltage.

Click herePower Source / Network>2AR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION


b.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




d.

Disconnect the fuel tube.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION


e.
A290066
2.5,0.25 2.583,0.25 2.583,0.25 2.771,0.542 false 0.75,0.333 0.833,0.333 0.833,0.333 1.292,0.417 false 0.833,0.75 0.917,0.75 0.917,0.75 1.135,0.583 false 1.667,1.25 1.75,1.25 1.75,1.25 1.917,0.906 false 1.135,1.25 1.333,1.583 1.333,1.583 1.417,1.583 false 0.583,1.167 0.667,1.167 0.667,1.167 0.771,1.281 false 1.229,2.958 1.417,3.167 1.417,3.167 1.5,3.167 false 1.25,3.802 1.417,4 1.417,4 1.5,4 false 0.667,3 0.75,3 0.75,3 0.927,3.135 false 1.521,3.063 1.833,3.219 0.313,0.156 10 *1 0.417,1.063 0.729,1.219 0.313,0.156 10 *2 1.438,1.479 1.75,1.635 0.313,0.156 10 *3 2.333,0.146 2.646,0.302 0.313,0.156 10 *4 1.521,3.896 1.833,4.052 0.313,0.156 10 *5 0.677,0.646 0.99,0.802 0.313,0.156 10 *6 0.583,0.24 0.896,0.396 0.313,0.156 10 *7 1.5,1.146 1.813,1.302 0.313,0.156 10 *6 0.5,2.896 0.813,3.052 0.313,0.156 10 *6
*1 SST (Hose)
*2 Fuel Tube
*3 SST (T Joint)
*4 SST (Pressure Gauge)
*5 SST (Fuel Tube Connector)
*6 SST (Hose Band)
*7 SST (Hose Joint)


Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


f.

Wipe up any gasoline.


g.

Reconnect the cable to the negative (-) battery terminal.


h.

Start the engine.


i.

Measure the fuel pressure at idle.

Fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


If the pressure is not as specified, check the fuel pump and injectors.


j.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent fuel from spilling.


k.