Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050877 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL CYLINDER HEAD STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A194964
1.198,2.156 1.406,2.333 0.208,0.177 10 *a 1.208,2.615 1.427,2.802 0.219,0.188 10 *c 1.635,2.354 1.854,2.531 0.219,0.177 10 *b
*a 18 mm (0.708 in.)
*b 33 mm (1.299 in.)
*c 13 mm (0.512 in.)


Using an E7 "TORX" socket wrench, install the cylinder head stud bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 2.INSTALL NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a straight screw plug or a plug is corroded, replace it.


a.

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 3.INSTALL NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a straight screw plug or a plug is corroded, replace it.


a.

Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 5.INSTALL VALVE STEM OIL SEAL

a.
A124785
1.01,0.771 1.521,1.417 1.521,1.417 1.521,1.49 true 2.5,0.771 2.063,0.927 2.063,0.927 2.063,1 true 0.698,0.031 0.969,0.208 0.271,0.177 10 *a 2.583,0.021 2.844,0.198 0.26,0.177 10 *b 1.365,0.302 1.594,0.469 0.229,0.167 10 *3 2,1.042 2.229,1.219 0.229,0.177 10 *2 1.469,1.531 1.688,1.719 0.219,0.188 10 *1
*1 Gray
*2 Black
*3 Mark "NOK"
*a Intake Side
*b Exhaust Side


Apply a light coat of engine oil to new oil seals.

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal onto the exhaust side or installing the exhaust oil seal onto the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gray and the exhaust valve oil seals are black.



b.
A194977
1.594,0.083 1.75,0.083 1.75,0.083 2.01,0.667 false 0.906,1.917 1.146,2.083 0.24,0.167 10 *a 2.208,1.917 2.448,2.094 0.24,0.177 10 *b 1.229,0 1.531,0.156 0.302,0.156 10 SST
*a CORRECT
*b INCORRECT


Using SST, push in the intake and exhaust valve oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 6.INSTALL INTAKE VALVE

a.
A285332
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.

Install the intake valve, compression spring and spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A194956
0.087,0.055 0.417,0.205 0.33,0.149 10 SST 1.904,0.075 2.234,0.224 0.33,0.149 10 SST 0.444,0.119 0.573,0.119 0.573,0.119 1.072,0.533 false 2.291,0.153 2.379,0.153 2.379,0.153 2.565,0.223 false

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010)


d.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.



Hide 7.INSTALL EXHAUST VALVE

a.
A285332
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Install the exhaust valve, compression spring and spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A194957
2.48,0.02 2.795,0.166 0.315,0.146 10 SST 2.444,0.092 2.306,0.092 2.306,0.092 2.205,0.682 false 0.753,1.67 1.068,1.816 0.315,0.146 10 SST 0.935,1.654 0.935,1.533 0.935,1.533 0.753,0.401 false

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010)


d.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.