FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) operates. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
Effects on each system when communication is impossible (for further details, see the pages for each system).
| System | Function | 1.
Control Master 2.
System Related 3.
Control Actuator |
Behavior during CAN Failure | ||
|---|---|---|---|---|---|
| Vehicle Behavior | Indicator and Buzzer | Diagnostic Trouble Code | |||
|
*: There is only output from the blind spot monitor sensor LH. |
|||||
| SFI | Electrical Load Control
(Performs idle up according to the electrical load.) |
1.
ECM 2.
Main body ECU (multiplex network body ECU), Air conditioning amplifier assembly, Power steering ECU assembly 3.
ECM |
Idle up according to the electrical load is not performed. | The idling speed changes. | - |
| Air Conditioning-linked Control
(Performs idle up according to the compressor load. Performs air conditioning cut control.) |
1.
ECM 2.
Air conditioning amplifier assembly 3.
Air conditioning amplifier assembly |
Air conditioning-linked control does not operate (cannot perform idle up). | Air conditioning does not operate. | - | |
| PTC Heater
(Performs idle up according to requests from the PTC heater [including coolant heater] or heater system.) |
1.
ECM 2.
Air conditioning amplifier assembly 3.
ECM |
The PTC heater does not operate (permission is not granted). | When there is a transmission stop or when the bus is continuously detected:
The PTC heater does not operate. When there is a reception stop:
·
The idling speed changes. ·
Heater performance becomes worse. ·
The PTC heater does not operate. |
- | |
| Eco-drive Indicator
(Displays information to the driver to encourage eco-driving.) |
1.
ECM 2.
- 3.
Combination meter assembly |
Nothing | No information is displayed. | - | |
| SFI | Integrated Control
(Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Power steering ECU assembly, Spiral with sensor cable sub-assembly (steering angle sensor) 3.
ECM |
Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved. | Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved. | - |
| ECT System Indicator
(Displays shift, switch and mode information to the meter.) |
1.
ECM 2.
Main body ECU (multiplex network body ECU) 3.
Combination meter assembly |
Nothing | ECT system indicators do not illuminate. | - | |
| Cruise Control
(Adjusts the engine throttle valve opening amount automatically to control the vehicle.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Combination meter assembly 3.
ECM |
Nothing | The cruise indicator blinks. | - | |
| Air Conditioning | Air Conditioner
·
The idle up engine speed, etc. is calibrated. ·
Adjusts the air temperature, airflow mode and airflow volume according to the engine coolant temperature. ·
Engine coolant temperature map calibration and compressor judgment value switching based on engine type. |
1.
Air conditioning amplifier assembly 2.
ECM 3.
- |
·
When there is a communication stop from the first time the ignition switch is turned to ON: Control is performed with the coolant temperature data set at the default value (80°C [176°F]). ·
When there is a communication stop while the ignition switch is ON: Maintains previous values. ·
When the ignition switch is not ON: Nothing |
If a communication stop occurs while the engine coolant temperature is rising, the airflow amount does not rise due to warm up control. | - |
·
When there is a communication stop from the first time +B is On and there is no DTF data: Control is performed with the engine type set at the default value. ·
When there is a communication stop in a situation other than described above: Maintains previous values. ·
When the ignition switch is not ON: Nothing |
When the AUTO SW is depressed, the compressor does not turn ON, or the compressor turns ON when it should not. | U0100 | |||
| Compressor Control
(Determines whether the compressor is locked according to NE.) |
1.
Air conditioning amplifier assembly 2.
ECM 3.
- |
·
When the ignition switch is ON: Control is performed with the default value (0 rpm). ·
When the ignition switch is not ON: Nothing |
The number of lines that turn ON by the PTC relay does not increase. | - | |
| Air Conditioning | Simple Load Control
(Limits simple electrical load control according to the load control level.) |
1.
Air conditioning amplifier assembly 2.
Power steering ECU assembly 3.
- |
·
When the ignition switch is ON: Maintains previous values (there is no load control during a reset). ·
When the ignition switch is not ON: Nothing |
The DEF relay and PTC relay do not turn ON. | U0131 |
| Destination Determination Control
(Switches air conditioning control pattern according to destination information.) |
1.
Air conditioning amplifier assembly 2.
Main body ECU (multiplex network body ECU) 3.
- |
·
When the ignition switch is ON: Maintains previous values. ·
When the ignition switch is not ON: Nothing |
The set temperature, unit, and central value on the panel cannot be changed. | U0142 | |
| Outside Temperature Compensation Control
(Changes the air conditioning system operation state and adjusts the outside temperature display value according to the vehicle information.) |
1.
Air conditioning amplifier assembly 2.
Combination meter assembly 3.
- |
·
When the ignition switch is ON: Control is performed with the vehicle speed set at the default value (0 km/h [0 mph]). ·
When the ignition switch is not ON: Nothing |
·
When the ignition switch is ON: ·
The reliability of the outside temperature value shown decreases. ·
The system is not able to adjust the air conditioning airflow volume correctly. ·
When the ignition switch is not ON: Nothing |
U0155 | |
| Main Body | Door Lock
(Operates the lock and unlock [the key-linked function, key lock-in prevention function, automatic lock function, etc.].) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM, Combination meter assembly Airbag sensor assembly 3.
Main body ECU (multiplex network body ECU) |
When there is a reception stop (ECM):
·
The speed-sensitive automatic door lock operation is prohibited. ·
The shift-linked automatic door lock operation is prohibited. ·
The shift-linked automatic door unlock operation is prohibited. ·
Automatic door lock switching is prohibited. When there is a reception stop (combination meter assembly):
The speed-sensitive automatic door lock operation is prohibited. When there is a reception stop (airbag sensor assembly):
·
When the ignition switch is ON: Maintains previous values. ·
When the ignition switch is off: The key-linked operation is permitted. |
Nothing | ·
U0100 ·
U0101 ·
U0151 ·
U0155 |
| Alarm
(Sounds various warnings.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM, Multiplex network door ECU 3.
Main body ECU (multiplex network body ECU) |
Nothing | Nothing | ·
U0100 ·
U0230 |
|
| Main Body | Automatic Dimming of Display
(Controls the display dimming.) |
1.
Main body ECU (multiplex network body ECU) 2.
Combination meter assembly 3.
Main body ECU (multiplex network body ECU) |
Automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed). | Nothing | U0155 |
| Illumination
(Performs illumination control.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM, Certification ECU (smart key ECU assembly) 3.
Main body ECU (multiplex network body ECU) |
·
The dome light is turned off. ·
The door mirror foot light is turned off. ·
The foot light is turned off. |
The dome light does not turn off immediately after exiting the vehicle. | ·
U0101 ·
U0327 |
|
| Seat Control
(Memory control [seat position adjustment]) |
1.
Main body ECU (multiplex network body ECU) 2.
Combination meter assembly, Certification ECU (smart key ECU assembly), Position control ECU and switch assembly 3.
Position control ECU and switch assembly |
·
Commands seat operation to be stopped. ·
When recording the memory call, the operation stops due to a time out when waiting for the verification results. |
Nothing | ·
U0208 ·
U0327 |
|
| Smart/Wireless
(Smart/wireless control) |
1.
Certification ECU (smart key ECU assembly) 2.
Main body ECU (multiplex network body ECU) 3.
Certification ECU (smart key ECU assembly) |
Entry lock/unlock control not possible. | Nothing | U0327 | |
| Lighting Control
(Performs DRL control) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM 3.
Main body ECU (multiplex network body ECU) |
Daytime running light control is not performed. | Nothing | U0100 | |
| Main Body | Back Door Opener
(Performs back door opener control and power back door one motion open control) |
1.
Main body ECU (multiplex network body ECU) 2.
Combination meter assembly, Multiplex network door ECU 3.
Main body ECU (multiplex network body ECU) |
·
Back door opener control is prohibited. ·
The back door operation start answer back (hazard warning light/buzzer) does not operate. ·
The one motion power back door does not operate. |
Nothing | ·
U0155 ·
U0230 |
| Navigation System | Eco Navigation Display
(Displays the average fuel consumption history and a graph indicating the fuel consumption in 1 minute intervals.) |
1.
Radio and display receiver assembly 2.
ECM, Combination meter assembly, Brake actuator assembly (skid control ECU) 3.
- |
·
The fuel consumption per minute display update on the eco navigation screen (fuel consumption per minute screen) stops (the fuel consumption per minute history graph is not cleared). ·
Stops updating the average fuel consumption history on the eco navigation (eco drive screen). ·
If the distance to empty is being displayed on the eco navigation (eco drive screen), the value displayed is cleared due to a distance to empty data communication stop. |
·
The 1 minute fuel consumption graph on the eco navigation (eco drive) display is not updated for 1 minute or more. ·
The most recent value for the fuel consumption interval graph on the eco navigation (eco drive) screen is cleared. ·
The numbers of the distance to empty displayed on the fuel consumption screen of the eco navigation (eco drive) display are cleared. |
·
U0100 ·
U0129 ·
U0155 |
| Navigation System | Rear View Monitor Control
(Displays the rear view monitor based on information from the steering sensor, the vehicle speed, and the vehicle information [2WD/4WD determination information, etc.].) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU), Spiral with sensor cable sub-assembly (steering angle sensor), ECM, Power steering ECU assembly, Brake actuator assembly (skid control ECU) 3.
- |
·
If a communication stop occurs when the expected course lines are being displayed, the expected course lines are cleared and "Guidance unavailable" is displayed on the bottom of the screen. ·
If a communication stop occurs when the display is in parallel parking guide mode, "Guidance unavailable" is displayed on the bottom of the screen. |
·
If a communication stop occurs while the expected course lines are displayed, the expected course lines are erased and "Guidance unavailable" is shown at the bottom of the screen. ·
If a communication stop occurs when the display is in parallel parking guide mode, "Guidance unavailable" is displayed on the bottom of the screen. ·
The screen does not change to the camera screen. ·
When the shift lever is moved to R and the camera screen is being displayed, a place other than the rear of the vehicle is displayed. |
·
U0100 ·
U0129 ·
U0131 ·
U0124 ·
U0126 ·
U0140 |
| Destination Determination
(Determines the destination of the vehicle and selects the display language, time zone, etc. based on destination symbols, destination package information, etc.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) 3.
- |
Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | The time zone and language selection screens do not match the destination. | U0140 | |
| Navigation System | Time Stamp Function
(Matches the relative time from the main body ECU with the absolute time acquired from the GPS.) |
1.
Main body ECU (multiplex network body ECU) 2.
Main body ECU (multiplex network body ECU) 3.
- |
Nothing | Nothing | ·
U0073 ·
U0140 |
| EPS | Electronic Power Steering System
(Calculates the current to be used for the steering assist according to the torque sensor value and vehicle speed, and then operates the motor.) |
1.
Power steering ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU), Spiral with sensor cable sub-assembly (steering angle sensor) 3.
- |
·
Power steering system does not operate. ·
Temporarily controls the vehicle with the assist amount fixed as if the vehicle were being driven at 100 km/h (62 mph). ·
The steering feel becomes worse (compensation control using the steering angle is stopped). |
The EPS warning light illuminates. | ·
U0100 ·
U0129 |
| Simple Load Control
(Determines the current power supply and load status, and sends commands to limit control.) |
1.
Power steering ECU assembly 2.
Power steering ECU assembly 3.
Air conditioning amplifier assembly |
Nothing | Nothing | - | |
| αB Control
(Performs assist to prevent sliding sideways.) |
1.
Brake actuator assembly (skid control ECU) 2.
Brake actuator assembly (skid control ECU) 3.
Power steering ECU assembly |
Control finishes if the CAN communication data becomes invalid during αB control. | The EPS warning light illuminates. | U0129 | |
| EPS | Steering Assist Calculation
(Changes the assist force according to the vehicle speed.) |
1.
Power steering ECU assembly 2.
Brake actuator assembly (skid control ECU) 3.
- |
·
As the vehicle speed cannot be determined, control continues with the vehicle speed set at 100 km/h (62 mph). ·
The steering wheel feels heavy when the vehicle speed is below 100 km/h (62 mph) and light when the vehicle speed exceeds 100 km/h (62 mph). |
The EPS warning light illuminates. | U0129 |
| DTC Output
(When the TC signal is on, DTC information is sent according to the polling from meter ECU.) |
1.
Combination meter assembly 2.
ECM, Power steering ECU assembly 3.
- |
Nothing | Nothing | - | |
| Assist Map Selection
(Selects the assist map according to the destination information, drivetrain [2WD or 4WD], engine type, etc.) |
1.
Power steering ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU) 3.
- |
·
A temporary map is used to perform assist as an assist map cannot be selected according to vehicle specifications. ·
Steering feel may be unusual. ·
The frame used to select the assist map may change depending on the vehicle. |
There is no indication of a communication problem. However, the EPS warning light illuminates because an assist map is not selected. | - | |
| Idle Up
(When a large assist current is created, request idle up to the ECM in order to prevent the battery voltage from dropping.) |
1.
ECM 2.
Power steering ECU assembly 3.
- |
Nothing | Nothing | - | |
| Warning Light Illumination
(When a fail-safe occurs, requests the meter ECU to illuminate the EPS warning light.) |
1.
Combination meter assembly 2.
Power steering ECU assembly 3.
- |
Nothing | Nothing | - | |
| EPS | Compensation Control
(Performs assist according to the vehicle speed for various compensation controls.) |
1.
Power steering ECU assembly 2.
Brake actuator assembly (skid control ECU) 3.
- |
When a CAN malfunction (vehicle speed malfunction) occurs, all controls operate as if the vehicle is being driven at 100 km/h (62 mph). | The EPS warning light illuminates. | U0129 |
| Stops air conditioning operation in order to decrease battery power consumption when the battery voltage decreases. | 1.
Power steering ECU assembly 2.
- 3.
Air conditioning amplifier assembly |
Nothing | Nothing | - | |
| Seat | Microcomputer Preset Position System
(Controls the memorized seat position according to vehicle information [power source mode, shift position, door, vehicle speed] and switch information [memory switch].) |
1.
Position control ECU and switch assembly 2.
ECM, Main body ECU (multiplex network body ECU), Combination meter assembly 3.
- |
·
The memory system does not operate. ·
The memory call function does not operate. ·
The return away function does not operate. |
·
The memory system does not operate. ·
The memory call function does not operate. ·
The return away function does not operate. |
- |
| Blind Spot Monitor | Blind Spot Monitor
(Warns the driver when the system detects a vehicle in the blind spots of the outer mirrors.) |
1.
Blind spot monitor sensor LH/RH 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Air conditioning amplifier assembly, Blind spot monitor sensor LH/RH 3.
Blind spot monitor sensor LH/RH |
Maintains previous values. | Blind spot monitor system warning displayed. | ·
U0100 ·
U0126 ·
U0129 ·
U0140 ·
U0232* |
| Steering Angle Sensor | Steering Sensor
(Detects steering wheel angle) |
1.
Spiral with sensor cable sub-assembly (steering angle sensor) 2.
Brake actuator assembly (skid control ECU) 3.
- |
Sends steering sensor data information every 12 seconds. | Nothing | - |
| Power Back Door | Power Back Door Open/Close Function
·
Automatically opens the back door according to the operation conditions (power source mode, shift position, vehicle speed, lock position) and switch operation (driver seat/wireless). ·
Automatically closes the back door according to switch operation (driver seat/wireless/back door). |
1.
Multiplex network door ECU 2.
ECM, Main body ECU (multiplex network body ECU), Combination meter assembly, Certification ECU (smart key ECU assembly) 3.
- |
·
Does not perform the automatic open and close operation. ·
The function cannot reverse operation during the automatic operation. |
·
There is no answer back with the buzzer or hazard warning lights when the automatic back door operation starts. ·
Does not perform the automatic open and close operation. ·
The wireless one motion function does not operate. ·
Stopping the automatic open or closing operation is not possible. ·
The function cannot reverse operation during the closer operation. |
- |
| Power Back Door | Wireless One Motion Function
(If a wireless switch operation is performed with the doors locked, the back door is automatically opened.) |
1.
Multiplex network door ECU 2.
ECM, Main body ECU (multiplex network body ECU), Combination meter assembly 3.
- |
The wireless one motion function does not operate. | The wireless one motion function does not operate. | - |
| Back Door Opener Function
(Opens the back door according to operation conditions [power source mode, vehicle speed, lock position] and the back door handle switch.) |
1.
Multiplex network door ECU 2.
Main body ECU (multiplex network body ECU), Combination meter assembly, Certification ECU (smart key ECU assembly) 3.
- |
The back door opener does not operate. | The back door opener does not operate. | - | |
| Back Door Closer Function
(Completely closes the back door when it is ajar.) |
1.
Multiplex network door ECU 2.
Main body ECU (multiplex network body ECU), Combination meter assembly, Certification ECU (smart key ECU assembly) 3.
- |
The function cannot reverse operation during the closer operation. | The function cannot reverse operation during the closer operation. | - | |
| Courtesy Switch Signal Substitution Output Function
(Sends a back door courtesy switch signal through the CAN bus.) |
1.
Multiplex network door ECU 2.
Main body ECU (multiplex network body ECU) 3.
- |
Nothing | When the back door opens, the indicator in the meter indicating the door is open does not illuminate | - | |
| Lock Permission Signal Output Function during Power Back Door Closing Operation
(Sends a power back door closing operation signal to the CAN bus in order to allow a wireless door lock during the power back door closing operation.) |
1.
Multiplex network door ECU 2.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly) 3.
- |
Nothing | Disallows the wireless lock during the power back door closing operation. | - | |
| Lane Departure Alert | LDW
(Warning when vehicle deviates from the lane.) |
1.
Lane departure warning camera 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Combination meter assembly 3.
Brake actuator assembly (skid control ECU) |
Stops detection and the buzzer output stops immediately. | A malfunction message is displayed. | ·
U0101 ·
U0129 ·
U0142 ·
U0155 |
| 4WD | ATC-4WD System
(Controls the driving force distribution between the front and rear wheels according to driving conditions.) |
1.
4WD ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Spiral with sensor cable sub-assembly (steering angle sensor), Air conditioning amplifier assembly 3.
4WD ECU assembly |
When transmission is lost:
4WD control is prohibited (the vehicle behaves the same as a 2WD vehicle). When there is a reception stop:
·
When the ECM or steering angle sensor is malfunctioning: Control continues using default values. ·
When the skid control ECU is malfunctioning: ·
Control is prohibited (the vehicle behaves the same as a 2WD vehicle). ·
Yaw rate feedback control is prohibited (conventional control continues). |
When there is a transmission stop or when the bus is continuously detected:
4WD indicator light blinks. When there is a reception stop or a cyclic malfunction:
4WD indicator light illuminates. |
·
U0073 ·
U0100 ·
U0126 ·
U0129 |
| 4WD | ATC-4WD System
(Controls the driving force distribution between the front and rear wheels according to driving conditions.) |
1.
4WD ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Spiral with sensor cable sub-assembly (steering angle sensor), Air conditioning amplifier assembly 3.
4WD ECU assembly |
During a cyclic malfunction:
·
During a steering angle sensor malfunction: ·
Control continues by maintaining previous values. ·
Control continues using default values. ·
During an ECM malfunction: Control continues using default values. ·
When the skid control ECU is malfunctioning: ·
Control continues using the default values (yaw rate feedback control). ·
Control continues, but the feedback of the speed difference between the front and rear wheels is prohibited. ·
When the air conditioning amplifier assembly or main body ECU is malfunctioning: Control continues using default values. |
When there is a transmission stop or when the bus is continuously detected:
4WD indicator light blinks. When there is a reception stop or a cyclic malfunction:
4WD indicator light illuminates. |
·
U0073 ·
U0100 ·
U0126 ·
U0129 |
| 4WD | ATC-4WD System
(Controls the driving force distribution between the front and rear wheels according to driving conditions.) |
1.
4WD ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Spiral with sensor cable sub-assembly (steering angle sensor), Air conditioning amplifier assembly 3.
4WD ECU assembly |
When a continuous bus is detected:
Control is prohibited (the vehicle behaves the same as a 2WD vehicle). |
When there is a transmission stop or when the bus is continuously detected:
4WD indicator light blinks. |
·
U0073 ·
U0100 ·
U0126 ·
U0129 |
| Meter | Vehicle Speed Display
(Operates the speedometer according the vehicle speed signals from the skid control ECU.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) 3.
- |
Signal is considered to be "0". | ·
Displays 0 km/h (0 mph) in the speedometer. ·
The drive monitor stops calculating. |
U0129 |
| Tachometer
(Displays the tachometer.) |
1.
Combination meter assembly 2.
ECM 3.
- |
Signal is considered to be "0". | ·
Displays 0 rpm in the tachometer. ·
The drive monitor stops calculating. |
U0100 | |
| Airbag
(Turns the airbag warning light on and off.) |
1.
Combination meter assembly 2.
Airbag sensor assembly 3.
- |
Signal is considered to be "Active". | The airbag warning light illuminates. | U0151 | |
| EPS Warning Light
(Turns the EPS warning light on and off.) |
1.
Combination meter assembly 2.
Power steering ECU assembly 3.
- |
Signal is considered to be "Active". | The EPS warning light illuminates. | U0131 | |
| SLIP Indicator Light
(Turns the SLIP indicator light on and off.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) 3.
- |
Signal is considered to be "Active". | The SLIP indicator illuminates. | - | |
| ECT/ENG System Display
(Displays the coolant temperature.) |
1.
Combination meter assembly 2.
ECM 3.
- |
Signal is considered to be "0". | The needle of the engine coolant temperature gauge is at the C mark or below. | - | |
| Brake | Anti-lock Brake System Control
(Prevents the wheels from locking when suddenly stopping.) |
1.
Brake actuator assembly (skid control ECU) 2.
- 3.
Brake actuator assembly (skid control ECU) |
·
During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control. ·
Not during control: Control cannot begin. |
·
The brake warning light illuminates. ·
The ABS warning light illuminates. ·
The SLIP indicator illuminates. |
U0073 |
| Vehicle Stability Control/Traction Control/Vehicle Dynamics Integrated Management Control
(Suppresses vehicle instability, such as drift when cornering and wheel slippage when accelerating. During vehicle dynamics integrated management control, vehicle integrated control which includes electronic steering control is performed.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Power steering ECU assembly, Spiral with sensor cable sub-assembly (steering angle sensor) 3.
Brake actuator assembly (skid control ECU) |
·
During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control. ·
Not during control: Control cannot begin. |
·
The brake warning light illuminates. ·
The ABS warning light illuminates. ·
The SLIP indicator illuminates. |
·
U0073 ·
U0100 ·
U0126 |
|
| Hill-start Assist Control 2
(Maintains the brake fluid pressure for 2 seconds when the brake pedal is depressed further.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Spiral with sensor cable sub-assembly (steering angle sensor) 3.
Brake actuator assembly (skid control ECU) |
·
During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control. ·
Not during control: Control cannot begin. |
·
The brake warning light illuminates. ·
The ABS warning light illuminates. ·
The SLIP indicator illuminates. |
·
U0073 ·
U0100 ·
U0126 |
|
| Eco Run Hold Control
(Maintains brake fluid pressure while switching from the brake pedal to the accelerator pedal and restarting the engine. The fluid pressure is maintained for a maximum of 2 seconds. Afterwards, it takes 1 second for the pressure to be released.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Spiral with sensor cable sub-assembly (steering angle sensor) 3.
Brake actuator assembly (skid control ECU) |
·
During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control. ·
Not during control: Control cannot begin. |
·
The brake warning light illuminates. ·
The ABS warning light illuminates. ·
The SLIP indicator illuminates. |
·
U0073 ·
U0100 ·
U0126 |
|
| Smart | Entry Function
·
Entry lock/unlock and smart back door unlatch ·
Entry warning ·
Entry illumination (Dome light illumination, etc.) |
1.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly) 2.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly) 3.
Main body ECU (multiplex network body ECU), Combination meter assembly |
An entry unlock retry is performed. | ·
Entry lock/unlock and smart back door unlatch ·
Entry warning does not operate. ·
Entry illumination does not operate. ·
The answer back function continuously operates when an unlock operation is performed. |
·
U0142 ·
U0155 |
1.
Certification ECU (smart key ECU assembly) 2.
ECM 3.
Combination meter assembly |
The previous value is maintained. | Falsely outputs the smart warning. | U0100 | ||
| Wireless Function
(Operates the wireless lock/unlock functions, etc.) |
1.
Main body ECU (multiplex network body ECU) 2.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly) 3.
Main body ECU (multiplex network body ECU) |
Nothing | Wireless lock/unlock and trunk functions do not operate. | - | |
| Smart | Memory Function
(Moves the seat to the memorized position when the doors are unlocked using the smart or wireless unlock.) |
1.
Main body ECU (multiplex network body ECU) 2.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly) 3.
Position control ECU and switch assembly |
Nothing | The memory recall function does not operate. | U0142 |
| Ignition Switch Illumination Control
(Operates ignition switch illumination in conjunction with the dome light illumination, etc.) |
1.
Certification ECU (smart key ECU assembly) 2.
Main body ECU (multiplex network body ECU), Certification ECU (smart key ECU assembly), Combination meter assembly 3.
Certification ECU (smart key ECU assembly) |
·
When the ignition switch letters are illuminated due to the dome light, the illumination turns off. ·
When the DC cut fuse is removed and the ignition switch letters are illuminated due to the panel illumination, the illumination turns off. ·
The previous value is maintained. |
·
If the ignition switch letters are not illuminated, they never illuminate. ·
If the ignition switch letters are illuminated due to the panel illumination, the illumination does not turn off. ·
When the ignition switch letters are illuminated due to the dome light, the illumination does not turn off. ·
When the DC cut fuse is removed and the ignition switch letters are illuminated due to the panel illumination, the illumination turns off. |
U0142 | |
| Airbag | TC DTC Output Service
(While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.) |
1.
Combination meter assembly 2.
ECM, Multiplex network door ECU 3.
Airbag sensor assembly |
If the TC signal is lost during TC service (TC=ON), the TC is determined to be OFF and TC service ends. | Nothing | - |
| Airbag | Timestamp
(Records DTCs and timestamps received from the main body ECU.) |
1.
Airbag sensor assembly 2.
Main body ECU (multiplex network body ECU) 3.
- |
Changes to a separate count inside the ECU and sets separate count recognition information when it receives a fail value or communication stops. | Nothing | - |
| Collision Detection Signal
(Notifies the system of a collision in order to perform fuel cut when a vehicle collision occurs.) |
1.
ECM 2.
Airbag sensor assembly 3.
- |
Nothing | Nothing | - | |
| Airbag Warning Light Control
(Sends airbag warning light illumination information.) |
1.
Combination meter assembly 2.
Airbag sensor assembly 3.
- |
Nothing | Nothing | - | |
| Seat Belt Warning Control
(Sends information about the passengers in order to turn the seat belt warning on and off.) |
1.
Main body ECU (multiplex network body ECU), Combination meter assembly 2.
Airbag sensor assembly 3.
- |
Nothing | Nothing | - | |
| Trigger Signal/Autonomous Transmission
(Outputs the yaw rate and acceleration sensor signal.) |
1.
Airbag sensor assembly 2.
Brake actuator assembly (skid control ECU) 3.
Brake actuator assembly (skid control ECU) |
Sends yaw rate sensor data information. | Nothing | - | |
| Event Data Recorder (EDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
1.
Airbag sensor assembly 2.
ECM, Brake actuator assembly (skid control ECU), Spiral with sensor cable sub-assembly (steering angle sensor) 3.
- |
·
When there is a communication error, a failure notification is received from the other device, or an invalid value is recorded in the EDR when the communication failure occurs. ·
When there is a periodic problem, the previous value is maintained. |
Nothing | - | |
| Airbag | Drive Data Recorder (DDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the drive data recorder recording conditions are met.) |
1.
Airbag sensor assembly 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU), Combination meter assembly, Power steering ECU assembly, Spiral with sensor cable sub-assembly (steering angle sensor) 3.
- |
·
When there is a communication error, a failure notification is received from the other device, or an invalid value is recorded in the DDR when the communication failure occurs. ·
When there is a periodic problem, the previous value is maintained. |
Nothing | - |