Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER
RM30B0U _59 Vehicle Exterior _009441 EXTERIOR PANELS / TRIM _0051127 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL FRONT BUMPER MOULDING

a.

Install the front bumper moulding with the 9 retainers.


Hide 2.INSTALL FRONT BUMPER GUARD

a.

Install the front bumper guard with the 8 retainers.


Hide 3.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.

Attach the 18 claws to install the lower No. 1 radiator grille.


Hide 4.INSTALL FRONT BUMPER EXTENSION LH

a.

Install the front bumper extension LH with the 5 retainers.


Hide 5.INSTALL FRONT BUMPER EXTENSION RH

HINT:

Use the same procedure described for the LH side.


Hide 6.INSTALL FRONT BUMPER ARM HOLE COVER LH

a.

Attach the 2 claws to install the front bumper arm hole cover LH.


Hide 7.INSTALL FRONT BUMPER ARM HOLE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 8.INSTALL FRONT BUMPER EMBLEM SUB-ASSEMBLY

a.

Attach the 2 claws to install the front bumper emblem sub-assembly.


Hide 9.INSTALL RADIATOR GRILLE GARNISH SUB-ASSEMBLY LH

a.

Attach the 4 clips to install the radiator garnish sub-assembly LH.


b.

Detach the claw.


c.

Install the 2 screws.


Hide 10.INSTALL RADIATOR GRILLE GARNISH SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

a.

Install the front bumper hole cover LH with the 2 screws.


b.

Install the clip.


Hide 12.INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 13.INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)

a.

Install the front bumper hole cover LH with the 2 screws.


b.

Install the clip.


Hide 14.INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 16.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 17.INSTALL HOOD TO FRONT END PANEL SEAL

HINT:

When installing the hood to front end panel seal, heat the front bumper cover using a heat light.


Standard:
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

When reusing the front bumper cover:

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

Install a new hood to front end panel seal.

i.

Using a heat light, heat the front bumper cover.


ii.

Remove the peeling paper from the face of the hood to front end panel seal.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 9 clips to install the hood to front end panel seal.

HINT:

Press the hood to front end panel seal firmly to install it.