Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM30B0U _59 Vehicle Exterior _009441 EXTERIOR PANELS / TRIM _0051135 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 4.REMOVE DOOR ASSIST GRIP COVER LH

Hide 5.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 7.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 8.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 9.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Hide 10.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 11.REMOVE REAR DOOR GLASS RUN LH

Hide 12.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 13.REMOVE REAR DOOR WEATHERSTRIP LH

B338469

a.

Remove the upper part of the rear door weatherstrip so that the rear door outside moulding sub-assembly can be removed.


Hide 14.REMOVE DOOR WINDOW FRAME MOULDING CLIP

B338471

a.

Detach the 2 claws and remove the door window frame moulding clip.


Hide 15.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

HINT:

When removing the window frame moulding, heat the rear door panel and window frame moulding using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear door panel and window frame moulding excessively.


a.
B340212
0.469,0.625 0.74,0.625 true 0.698,1.344 0.969,1.344 true 1.49,1.635 1.49,1.438 1.49,1.438 1.708,1.438 true 1.344,0.25 1.344,0.115 1.344,0.115 1.552,0.115 true 1.583,0.042 1.896,0.198 0.313,0.156 10 *1 0.313,0.542 0.625,0.698 0.313,0.156 10 *2 1.729,1.365 2.042,1.521 0.313,0.156 10 *1 1,1.26 1.313,1.417 0.313,0.156 10 *2
*1 Protective Tape
*2 Double-sided Tape


Put protective tape around the rear door outside moulding sub-assembly LH.


b.

Using a moulding remover, detach the clip.


c.

Detach the clip and remove the double-sided tape to remove the rear door outside moulding sub-assembly LH.