Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM30B0U _59 Vehicle Exterior _009441 EXTERIOR PANELS / TRIM _0051138 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE ROOF RACK ASSEMBLY LH (w/ Roof Rack)

Hide 2.REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER LH (w/o Roof Rack)

HINT:

Use the same procedure for both roof drip side finish moulding joint covers.


a.
B338483
1.354,1.854 1.865,1.854 1.865,1.854 1.865,1.365 true 1.167,1.771 1.479,1.969 0.313,0.198 10 *1
*1 Protective Tape


Put protective tape around the roof drip side finish moulding joint cover LH.


b.

Using moulding remover D, detach the clip and claw and remove the roof drip side finish moulding joint cover LH.


Hide 3.REMOVE ROOF DRIP SIDE FINISH MOULDING LH

a.
B338484
2.031,1.729 1.802,1.729 1.802,1.729 1.802,1.24 true 2.104,1.656 2.417,1.854 0.313,0.198 10 *1
*1 Protective Tape


Put protective tape around the roof drip side finish moulding LH.


b.

Using moulding remover D, detach the clip and remove the roof drip side finish moulding LH.

NOTICE:
·

When removing the roof drip side finish moulding, be careful not to damage the roof drip side finish moulding clips.

·

If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.




Hide 4.REMOVE CENTER NO. 2 ROOF DRIP SIDE FINISH MOULDING LH

B338486
1.646,1.469 1.646,1.865 1.646,1.865 1.938,1.865 true 2.01,1.792 2.323,1.99 0.313,0.198 10 *1
*1 Protective Tape


a.

Put protective tape around the center No. 2 roof drip side finish moulding LH.


b.

Using moulding remover D, remove the center No. 2 roof drip side finish moulding LH.


Hide 5.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH

a.
B338487
1.854,1.458 1.854,1.74 1.854,1.74 2.052,1.74 true 2.146,1.656 2.458,1.854 0.313,0.198 10 *1
*1 Protective Tape


Put protective tape around the rear roof drip side finish moulding LH.


b.

Using moulding remover D, detach the clip and remove the rear roof drip side finish moulding LH.

NOTICE:
·

When removing the rear roof drip side finish moulding, be careful not to damage the roof drip side finish moulding clips.

·

If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.




Hide 6.REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP (for Front Side)

B338485

HINT:

Perform the following procedures if replacing a roof drip side finish moulding clip.


a.

Using a heat light, heat the clip and vehicle body.

NOTICE:

Do not heat the clip and vehicle body excessively.



b.

Remove the roof drip side finish moulding clip.


Hide 7.REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP (for Rear Side)

B338488

HINT:

Perform the following procedures if replacing a roof drip side finish moulding clip.


a.

Using a heat light, heat the clip and vehicle body.

NOTICE:

Do not heat the clip and vehicle body excessively.



b.

Remove the roof drip side finish moulding clip.


Hide 8.REMOVE FRONT ROOF RACK BRACKET (w/o Roof Rack)

B338489

a.

Remove the 2 bolts and front roof rack bracket.


Hide 9.REMOVE REAR ROOF RACK BRACKET (w/o Roof Rack)

B338490

a.

Remove the 2 bolts and rear roof rack bracket.