FREEZE FRAME DATA
Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the blind spot monitor main switch (warning cancel switch assembly) on.
Turn the Techstream on.
Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Trouble Codes.
According to the display on the Techstream, display the Freeze Frame Data for the selected DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | Blind spot monitor main switch (warning cancel switch assembly) | OFF or ON | ON: Blind spot monitor main switch (warning cancel switch assembly) on
OFF: Blind spot monitor main switch (warning cancel switch assembly) off |
- |
| Warning Indicator Turning on(Master) | State of the outer rear view mirror indicator LH turning on | OFF or ON | OFF: The following conditions are not met
ON: All of the following conditions are met ·
Not during initial check ·
Vehicle detected in left hand side warning area ·
Left turn signal: off ·
Vehicle speed 16 km/h (10 mph) or more ·
Shift lever in any position except R ·
Blind spot monitor warning light not illuminated |
- |
| Warning Indicator Flashing(Master) | State of the outer rear view mirror indicator LH flashing | OFF or ON | OFF: The following conditions are not met
ON: All of the following conditions are met ·
Not during initial check ·
Vehicle detected in left hand side warning area ·
Left turn signal: on ·
Vehicle speed 16 km/h (10 mph) or more ·
Shift lever in any position except R ·
Blind spot monitor warning light not illuminated |
- |
| Main Switch Indicator Status | State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) | OFF or ON | OFF: Indicator not illuminated
ON: Indicator illuminated |
- |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Not illuminated: 0 mA
Illuminated: 5 to 100 mA |
- |
| Main Switch Indicator Input Circuit Voltage | Blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) voltage | Min.: 0 V, Max.: 25.5 V | Always: 9 to 16 V | - |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) | Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0
When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Warning Indicator Turning on(Slave) | State of the outer rear view mirror indicator RH turning on | OFF or ON | OFF: The following conditions are not met
ON: All of the following conditions are met ·
Not during initial check ·
Vehicle detected in right hand side warning area ·
Right turn signal: OFF ·
Vehicle speed 16 km/h (10 mph) or more ·
Shift lever in any position except R ·
Blind spot monitor warning light not illuminated |
- |
| Warning Indicator Flashing(Slave) | State of the outer rear view mirror indicator RH flashing | OFF or ON | OFF: The following conditions are not met
ON: All of the following conditions are met ·
Not during initial check ·
Vehicle detected in right hand side warning area ·
Vehicle speed 16 km/h (10 mph) or more ·
Right turn signal: ON ·
Shift lever in any position except R ·
Blind spot monitor warning light not illuminated |
- |
| Buzzer Sound Status | State of the rear cross traffic alert buzzer (blind spot monitor buzzer) | OFF or ON | OFF: Buzzer not sounding
ON: All of the following conditions are met: ·
Not during initial check ·
Vehicle detected in warning area of rear cross traffic alert ·
Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more ·
Shift lever in R ·
No DTC output |
w/ Rear Cross Traffic Alert |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Not illuminated: 0 mA
Illuminated: 5 to 100 mA |
- |
| Buzzer Input Circuit Voltage | Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage | Min.: 0 V, Max.: 25.5 V | Not sounding buzzer: 11 to 14 V Sounding buzzer: Alternating between 0 to 14 V | w/ Rear Cross Traffic Alert |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) | Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0
When a malfunction is detected: More than 0 |
- |
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the Freeze Frame Data
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the blind spot monitor main switch (warning cancel switch assembly) on.
Turn the Techstream on.
Clear the DTCs and Freeze Frame Data.