Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT
RM30B0U _52 Drivetrain _009469 AXLE AND DIFFERENTIAL _0051190 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DISCONNECT FRONT FLEXIBLE HOSE

a.
C153576

Remove the bolt and disconnect the flexible hose.


Hide 3.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C130484

Remove the 2 bolts and disconnect the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



Hide 4.REMOVE FRONT DISC

Hide 5.REMOVE FRONT AXLE HUB BOLT LH

C159676
1.49,0.406 2.302,0.406 false 2.188,2.083 2.406,1.76 false 2.406,1.76 2.771,1.76 false 0.479,2.635 1.354,2.323 false 0.49,2.646 1.521,2.552 false 0.302,2.573 0.615,2.729 0.313,0.156 10 *1 0.938,3.083 1.25,3.24 0.313,0.156 10 *a 2.375,2.875 2.688,3.031 0.313,0.156 10 *b 1.167,0.313 1.625,0.51 0.458,0.198 10 SST 2.823,1.688 3.281,1.885 0.458,0.198 10 SST
*1 Nut
*a Hold
*b Turn


a.

Temporarily install 2 nuts and 2 washers to the front axle hub bolt as shown in the illustration.


b.

Using SST and a brass bar or an equivalent tool to hold the front axle, remove the front axle hub bolt.

SST
09611-12010  


Hide 6.INSTALL FRONT AXLE HUB BOLT LH

a.
C159674
1.417,0.375 1.906,0.375 false 2.625,1.063 1.906,0.375 false 2.906,1.135 3.104,0.417 false 0.531,2.656 1.365,2.073 false 0.542,2.656 1.542,2.333 false 1.24,0.292 1.552,0.448 0.313,0.156 10 *1 3.052,0.24 3.365,0.396 0.313,0.156 10 *2 1.292,3.135 1.604,3.292 0.313,0.156 10 *a 2.885,2.24 3.198,2.396 0.313,0.156 10 *b 0.354,2.604 0.667,2.76 0.313,0.156 10 *2
*1 Washer
*2 Nut
*a Hold
*b Turn


Install a washer and nut to a new front axle hub bolt as shown in the illustration.


b.

Using a brass bar or an equivalent tool to hold the front axle, install the hub bolt by tightening the nut.


c.

Remove the nut and plate washer.


Hide 7.INSTALL FRONT DISC

Hide 8.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.

Connect the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the steering knuckle with the bolt.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 10.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)