Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2WD)
RM30B0U _52 Drivetrain _009984 DRIVE SHAFT / PROPELLER SHAFT _0054768 FRONT DRIVE SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2WD)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

C127644
0.094,0.135 0.406,0.333 0.313,0.198 10 *A 0.094,2.24 0.406,2.438 0.313,0.198 10 *B
*A for One Touch Type
*B for Claw Engagement Type


a.

for One Touch Type:

Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


b.

for Claw Engagement Type:

Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


Hide 2.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 3.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.


Hide 4.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 5.DISCONNECT FRONT AXLE INBOARD JOINT BOOT

a.

Disconnect the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

C127646
2.167,0.396 2.167,0.25 2.167,0.25 1.083,0.25 true 1.833,0.802 1.833,0.25 true 0.875,0.167 1.167,0.354 0.292,0.188 10 *a
*a Matchmark


a.

Remove any old grease from the front drive inboard joint assembly LH.


b.

Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.


d.
C127648

Using a snap ring expander, remove the snap ring.


e.
C127649
2.677,0.76 2.677,1.542 2.677,1.542 2.938,1.542 true 2.802,0.844 2.802,1.531 true 3,1.438 3.313,1.635 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



f.

Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

NOTICE:

Do not tap the rollers.



g.

Remove the front axle inboard joint boot.


Hide 7.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 8.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH

C127651
0.063,0.031 0.271,0.198 0.208,0.167 10 *A 0.073,2.292 0.302,2.469 0.229,0.177 10 *B
*A for One Touch Type
*B for Claw Engagement Type


a.

for One Touch Type:

Using a screwdriver, remove the front drive shaft damper clamp LH as shown in the illustration.


b.

for Claw Engagement Type:

Using needle-nose pliers, remove the front drive shaft damper clamp LH as shown in the illustration.


Hide 9.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 10.REMOVE FRONT DRIVE SHAFT DAMPER LH

a.

Remove the front drive shaft damper LH from the front drive outboard joint shaft assembly LH.


Hide 11.REMOVE FRONT DRIVE SHAFT DAMPER RH

HINT:

Use the same procedure described for the LH side.


Hide 12.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

a.

for TMMC Made:

i.
C160725

Using pliers, remove the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.



b.

except TMMC Made:

i.
C127653

Using a screwdriver, remove the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.



Hide 13.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 14.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.


Hide 15.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 16.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot from the front drive outboard joint shaft assembly.


b.

Remove any old grease from the front drive outboard joint shaft assembly.


Hide 17.REMOVE FRONT DRIVE SHAFT DUST COVER LH

C127659
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

a.

Using SST and a press, remove the front drive shaftdust cover LH.

SST
09950-00020  

NOTICE:

Be careful not to drop the front drive inboard joint assembly LH.



Hide 18.REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 19.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
C127664
1.219,1.5 1.021,1.323 1.021,1.323 0.625,1.323 true 0.281,1.24 0.573,1.385 0.292,0.146 10 SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

SST
09950-00020  

NOTICE:

Be careful not to drop the front drive inboard joint assembly RH.



Hide 20.REMOVE FRONT DRIVE SHAFT BEARING

C127665

a.

Using a snap ring expander, remove the snap ring.


b.
C127666
2.615,0.906 2.417,0.906 2.417,0.906 2.177,1.479 true 2.698,0.833 3.01,0.99 0.313,0.156 10 SST

Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

SST
09527-10011  

NOTICE:

Be careful not to drop the front drive inboard joint assembly RH.