READ DATA LIST
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | ON or OFF | ON: OPEN switch pressed
OFF: OPEN switch not pressed |
- |
| Close Switch | CLOSE switch signal | ON or OFF | ON: CLOSE switch pressed
OFF: CLOSE switch not pressed |
- |
| Up Switch | UP switch signal | ON or OFF | ON: UP switch pressed
OFF: UP switch not pressed |
- |
| Down Switch | DOWN switch signal | ON or OFF | ON: DOWN switch pressed
OFF: DOWN switch not pressed |
- |
| Rear SW Auto Operation | Sliding roof auto function | ON or OFF | Customization status displayed | This item is not applicable to this vehicle |
| Front SW Auto Operation | Sliding roof auto function | ON or OFF | Customization status displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal
Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low
Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal
Error: Hall IC2 not normal |
- |
| Ignition (Direct Signal) | Ignition switch signal | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
- |
| Ignition (MPX) | Ignition switch signal (LIN signal) | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
- |
| Door Courtesy | Driver door courtesy light switch signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Door Handle Lock Button | Entry lock switch | ON or OFF | ON: Entry lock switch is pressed
OFF: Entry lock switch is not pressed |
This item is not applicable to this vehicle |
| Door Key Close Operation | Key-linked sliding roof close signal | ON or OFF | ON: Door LOCK is turned to close position using key
OFF: Door LOCK is not turned |
This item is not applicable to this vehicle |
| Door Key Open Operation | Key-linked sliding roof open signal | ON or OFF | ON: Door UNLOCK is turned to open position using key
OFF: Door UNLOCK is not turned |
This item is not applicable to this vehicle |
| Wireless Close Operation | Wireless sliding roof close signal | ON or OFF | ON: Transmitter LOCK switch pressed
OFF: Transmitter LOCK switch not pressed |
This item is not applicable to this vehicle |
| Wireless Open Operation | Wireless sliding roof open signal | ON or OFF | ON: Transmitter UNLOCK switch pressed
OFF: Transmitter UNLOCK switch not pressed |
This item is not applicable to this vehicle |
| Key Off Permission | Key-off sliding roof operation permit signal | ON or OFF | ON: Front doors are not opened within 43 seconds after ignition switch turned off
OFF: Any status except "ON" status |
- |
| Window Lock | Window lock operation signal | ON or OFF | ON: Window lock switch is turned to lock
OFF: Window lock switch is turned to unlock |
This item is not applicable to this vehicle |
| Door Key Related Operation | Key-linked sliding roof open function operating direction | Slide or Tilt | Customization status displayed | This item is not applicable to this vehicle |
| Wireless Key Rel Operation | Wireless transmitter-linked sliding roof open function operating direction | Slide or Tilt | Customization status displayed | This item is not applicable to this vehicle |
| Open Switch Failure(Past) | Open switch failure signal (Past) | ON or OFF | ON: Sliding roof open switch failure signal (Past)
OFF: No sliding roof open switch failure signal (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | ON or OFF | ON: Sliding roof close switch failure signal (Past)
OFF: No sliding roof close switch failure signal (Past) |
- |
| Up Switch Failure(Past) | Up switch failure signal (Past) | ON or OFF | ON: Sliding roof tilt up switch failure signal (Past)
OFF: No sliding roof tilt up switch failure signal (Past) |
- |
| Down Switch Failure(Past) | Down switch failure signal (Past) | ON or OFF | ON: Sliding roof tilt down switch failure signal (Past)
OFF: No sliding roof tilt down switch failure signal (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current) | ON or OFF | ON: Sliding roof open switch failure signal (Current)
OFF: No sliding roof open switch failure signal (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | ON or OFF | ON: Sliding roof close switch failure signal (Current)
OFF: No sliding roof close switch failure signal (Current) |
- |
| Up Switch Failure(Current) | Up switch failure signal (Current) | ON or OFF | ON: Sliding roof tilt up switch failure signal (Current)
OFF: No sliding roof tilt up switch failure signal (Current) |
- |
| Down Switch Failure(Current) | Down switch failure signal (Current) | ON or OFF | ON: Sliding roof tilt down switch failure signal (Current)
OFF: No sliding roof tilt down switch failure signal (Current) |
- |
| Number of Trouble Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of stored DTCs | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Slide Roof Open Warning | Sliding roof open warning | ON or OFF | Customization status displayed | - |
PERFORM ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Sliding Roof / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof motor | OFF / Opn/Dwn / Clos/Up | - |