Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the Techstream to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

E236715
4.646,5.083 5.094,5.344 0.448,0.26 3,5.083 3.448,5.344 0.448,0.26 2.708,6.469 3.156,6.729 0.448,0.26 1.375,4.198 1.823,4.458 0.448,0.26 1.375,5.625 1.823,5.885 0.448,0.26 0.5,7.854 0.948,8.115 0.448,0.26 1.552,0.323 4.333,1.135 2.781,0.813 10 Turn the ignition switch to ON while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears. 4.583,1.188 6.667,1.865 2.083,0.677 10 The "AUTO" and "Recirculation/Fresh" switches are not pressed at the same time. 2.25,2.74 3.625,3.25 1.375,0.51 10 Indicator Check (continuous operation) 2.115,4.167 3.823,4.51 1.708,0.344 10 Sensor Check (DTC check) (continuous operation) 2.083,5.604 3.792,5.948 1.708,0.344 10 Sensor Check (DTC check) (step operation) 4.698,5.125 5.104,5.281 0.406,0.156 10 AUTO 3.042,5.125 3.521,5.313 0.479,0.188 10 UP Dr 2.74,6.51 3.146,6.667 0.406,0.156 10 UP Dr 1.594,7.188 4.438,7.51 2.844,0.323 10 Check mode is canceled and air conditioning control starts 1.458,4.24 1.865,4.396 0.406,0.156 10 OFF 1.469,5.667 1.875,5.823 0.406,0.156 10 OFF 1,7.906 2.75,8.146 1.75,0.24 10 : Indicates switch operation 0.719,8.333 2.417,8.552 1.698,0.219 10 OFF: Blower fan off switch 3.104,8.333 5.677,8.573 2.573,0.24 10 UP Dr: Driver side temperature up switch 3.104,7.896 5.677,8.156 2.573,0.26 10 AUTO: Automatic air conditioning switch



INDICATOR CHECK


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC and wait at least 5 seconds.


c.
E269938

Turn the ignition switch to ON while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.


d.
E269939
0.146,2.375 0.458,2.531 0.313,0.156 10 false *a 0.823,3.01 1.135,3.167 0.313,0.156 10 false *b 0.823,3.677 1.135,3.833 0.313,0.156 10 false *c 1.135,2.677 1.448,2.833 0.313,0.156 10 false *d 1.896,2.698 2.208,2.854 0.313,0.156 10 false *d
*a Indicator Blinking Pattern
*b On
*c Off
*d 1 second


The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel check mode.





SENSOR CHECK (DTC CHECK)


a.

Start the engine and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.
E269940
1.25,0.865 1.385,0.354 1.385,0.354 1.563,0.354 true 1.615,0.25 1.927,0.448 0.313,0.198 10 *a
*a Diagnostic Trouble Code (DTC)


Read the DTC displayed on the indicator panel.

NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DIAGNOSTIC TROUBLE CODE CHART

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that DTC 12 is output.




d.
E269941

If the DTCs are difficult to read because they change automatically, turn the "Driver TEMP" switch clockwise to display the DTCs one at a time so that they can be read easily. The DTCs change step by step each time the "Driver TEMP" switch is turned clockwise.

HINT:

Press the "OFF" switch to finish panel diagnosis.



e.

Clear DTCs

i.
E269942

During the sensor check, press the front defroster switch and rear defogger switch simultaneously.