The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.
| Control ECU | Condition |
|---|---|
| Air Conditioning Amplifier Assembly | Engine running |
| Combination switch assembly (ECO mode switch) off | |
| Blower motor on | |
| Temperature set to MAX HOT | |
| IDH terminal signal less than 1 V
(Inverter with converter assembly overload not detected) |
|
·
Engine coolant temperature 65°C or less (2 heaters operate) ·
Engine coolant temperature 75°C or less (A heater operates) |
|
| Ambient temperature 10°C or less |
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Heater Active Level | Quick heater assembly | Min.: 0, Max.: 3 | - |
| Tester Display |
|---|
| Heater Active Level |
| Proceed to |
|---|
| Heater Active Level changes normally |
| Heater Active Level does not change normally |
Heater Active Level changes normally
Heater Active Level does not change normally
Remove the PTC heater relays from No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage is applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | PTC HTR NO.1 relay |
| *2 | PTC HTR NO.2 relay |
| *a | Component without relay installed
(No. 2 Engine Room Relay Block) |
Remove the PTC heater relays from No. 2 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - Body ground | Always | 11 to 14 V |
| 2 - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - Body ground | Always | 11 to 14 V |
| 2 - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G80 air conditioning amplifier assembly connector.
Remove the PTC heater relays from No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - G80-13 (PTC1) | Always | Below 1 Ω |
| 1 - G80-19 (PTC2) | Always | Below 1 Ω |
| G80-13 (PTC1) - Body ground | Always | 10 kΩ or higher |
| G80-19 (PTC2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the PTC heater relays from No. 2 engine room relay block.
Disconnect the A31 quick heater assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - A31-1 (B) | Always | Below 1 Ω |
| A31-1 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - A31-3 (B) | Always | Below 1 Ω |
| A31-3 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A32 quick heater assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-1 (E) - Body ground | Always | Below 1 Ω |
| A32-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>REMOVAL
Inspect the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG