Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM30B0U _58 Vehicle Interior _009874 DOOR LOCK _0054787 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

a.
B164415
1.104,3.802 1.104,3.031 1.104,3.031 1.198,3.031 true 0.583,3.813 0.583,3.042 0.583,3.042 0.365,3.042 true 0.219,0.135 0.969,0.656 0.75,0.521 10 *a 1.781,3.906 2.167,4.26 0.385,0.354 10 *c 2.292,3.938 2.656,4.25 0.365,0.313 10 *b 0.24,2.958 0.469,3.167 0.229,0.208 10 L 1.25,2.958 1.719,3.24 0.469,0.281 10 UL
*a Component without harness connected
(Rear Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the rear door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door with motor lock assembly LH.



b.
B164415
1.021,4.073 1.021,4.417 1.021,4.417 1.125,4.417 true 0.667,4.073 0.667,4.417 0.667,4.417 0.563,4.417 true 0.219,0.156 0.781,0.542 0.563,0.385 10 *a 1.781,3.938 2.115,4.229 0.333,0.292 10 *c 2.292,3.948 2.677,4.198 0.385,0.25 10 *b 0.427,4.354 0.542,4.49 0.115,0.135 10 E 1.167,4.344 1.552,4.479 0.385,0.135 10 LSSR
*a Component without harness connected
(Rear Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch (w/ Smart Entry and Start System or Theft Deterrent System).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door with motor lock assembly LH.



Hide 2.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY RH

a.
B164416
1.115,3.802 1.115,3 1.115,3 1.26,3 true 0.583,3.802 0.583,3 0.583,3 0.406,3 true 0.24,0.198 0.76,0.542 0.521,0.344 10 *a 2,3.917 2.292,4.156 0.292,0.24 10 *b 2.458,3.927 2.865,4.25 0.406,0.323 10 *c 1.292,2.938 1.604,3.177 0.313,0.24 10 UL 0.281,2.927 0.521,3.271 0.24,0.344 10 L
*a Component without harness connected
(Rear Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the rear door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door with motor lock assembly RH.



b.
B164416
0.677,4.073 0.677,4.427 0.677,4.427 0.5,4.427 true 1.031,4.073 1.031,4.427 1.031,4.427 1.229,4.427 true 0.24,0.146 0.906,0.573 0.667,0.427 10 *a 2.01,3.896 2.375,4.167 0.365,0.271 10 *b 2.438,3.906 2.813,4.188 0.375,0.281 10 *c 1.281,4.333 1.927,4.583 0.646,0.25 10 LSSR 0.365,4.354 0.719,4.646 0.354,0.292 10 E
*a Component without harness connected
(Rear Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch (w/ Smart Entry and Start System or Theft Deterrent System).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door with motor lock assembly RH.